Considering the 9-10 month backlog of orders, there
must be a lot of folks who have ..."lost all their good
sense"... .
73, Dick, W1KSZ
On Mon, Nov 9, 2015 at 2:33 PM, Leigh Turner <invertech@frontierisp.net.au>
wrote:
>
> Hi Jim,
>
> I fully concur with all of your points below.
>
> Someone would have to have lost all of their good sense to even consider
> buying an amplifier without a complete set of detailed schematic diagrams
> and associated Parts List. It is the ultimate insult to their customers and
> the epitome of arrogance for a manufacturer not to do so.
>
> To be considerate of other band users, one would have to operate the
> 1.3K-FA
> "linear" amplifier with considerable Po back-off below the amp's rated 1300
> Watts PEP that's well clear of its 1 dB power compression point and
> saturated Po to yield any half-decent / semi-respectable IMD figures.
>
> Leigh
> VK5KLT
>
> -----Original Message-----
> From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Jim Thomson
> Sent: Monday, 9 November 2015 9:45 PM
> To: amps@contesting.com
> Subject: [Amps] Question about SPE 1.3K-FA amplifier
>
> Date: Sun, 8 Nov 2015 06:59:35 -0700
> From: Richard Solomon <dickw1ksz@gmail.com>
> To: Amps group <amps@contesting.com>
> Subject: Re: [Amps] Question about SPE 1.3K-FA amplifier
>
> Here is a link to what looks like the Test Report for
> FCC Type Acceptance.
>
> https://fccid.io/pdf.php?id=2443307
>
> Curious as to what folks think about the results.
>
> ## This is almost as good as an arrl report for basic stuff.
> Their test method seems a bit flawed imo. You can't test
> any linear amp, by stuffing a 2 tone signal into the mic jack.
> Unless the xcvr is running in class A. In this case, the icom 7800
> used for the test, afaik, does not run class A.
>
> ## If SPE cant / doesn't want to provide a schematic for this amp,
> or any of their other amps, I would not touch it, or buy one.
>
> ## at least they provide imd info for imd3 to imd11.
>
> ## The imd test is further flawed.... since they only ran the test at 1000
> w pep out. The harmonic test was run at 1300w out. They are also stated
> in
> db below pep, and not db below one tone. So u have to subtract 6 db from
> all their tables. IE: their IMD3 on 7.150 mhz is a lousy -27.6 db. (and a
> lousy -24.8 db on 160m and also 10m). Again, re-run the test at 1300w pep
> out, and imd results will be a helluva lot worse.
>
> ## They need to re-run the test, this time using TWO xcvrs, each feeding a
> cxr into a hybrid etc, then into the input of the amp.....and do it with
> the
> amp running 1.3 kw pep out.
>
> Jim VE7RF
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|