Hi Gerald,
One of the guys brought up the idea that the vacuum relay may have
reached the end of it's life, but we didn't check it out at that point.
It was NOS when I got it 30 years ago, and no telling how many cycles
it's gone thru in the many THOUSANDS of QSO's that were made using that amp.
Thanks for the data point. We will check it out.
73 de Steve, NR4M
On 5/28/2015 00:46 , TexasRF@aol.com wrote:
Hi Steve, you might try putting a short strap across the vac relay
terminals for a test.
It sounds as if you might be loosing the plate load in an erratic manner.
73,
Gerald K5GW
In a message dated 5/27/2015 6:47:20 P.M. Central Daylight Time,
steve@nr4m.com writes:
Hello all,
Since it's gotten quiet here, i thought I would get the collective
'gray
matter' working again.
I am having a strange problem with a homebrew 8877 amp. It has worked
almost flawlessly for 30 years with the same tube and still easily
puts
out legal power. 4000 volts at a load of about 550 ma., driving with
about 22 watts.
During the night shift in CQWW (I believe) the amp started acting
up and
was replace with a spare. It is a 40 meter mono band amp.
I was told that there was no output but 'the meters still were
'jumping
around''. I opened it up expecting to find an obvious issue with the
vacuum relay on the output. Power has to go SOMEWHERE, right? All
looked as good as it ever did.
Just before Dayton, myself and two budddies, fired up the amp, after
once again looking inside.
This is what I am seeing:
We tuned it up with 10 watts drive into a oil filled dummy load
and got
700-750 watts out with a few hundred mils of plate current and
about 10
mils of grid current. Unkeyed it and then rekeyed it. Upon rekeying,
the 100 mil grid meter slammed and the grid trip circuit did it's
job.
I have it set for 75 mils of grid current. Wound up reducing the grid
capacitance so that the max grid current would be more reasonable.
After trying it on/off again and again, when it goes 'nuts', the grid
current stays on the scale at about 60 mils and about 'just a little
bit' when it seems to conduct normally. When it acts up, if I
turn the
TUNE vacuum variable just a wee bit, I get my plate current as I
should
and the grid current goes down to normal. My multi turn counter
on the
TUNE cap is marked '0 to 100' on the knob skirt and a 'wee bit' is
from
88 to 96, just 8 marks, or 8% of one turn. This is on a 375 pf vac
variable cap.
Taping on the chassis would make the problem come and go, but not
every
time and not easily. Try it again and I would have to turn the cap
back the other way to resonate it (seemingly.)
In my mind, it seems like something in the RF side of things, since
changing the cap brings it back from the 'dark side'. Keying the amp
with no drive and swinging the caps back and forth showed no
instability. I also took all the connections in the tank circuit
apart
looking for loose joints and corrosion. None found. Reseated the
tube.
Works fine every time till it doesn't.
It's doing the same thing as I think I would expect to see if I
manually
de-tuned the tank circuit with the input cap. It also showed plate
current during the 'event', although lower than normal, so where
is the
power going? Quiescent plate current is about 120 mils.
Any ideas out there? I can supply pics if needed. Maybe I should
record the event and put it on you tube with a link.
Look for some of you this weekend in the WPX CW contest.
73 de Steve, NR4M
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|