Hmmmm, without a callsign you may even be a CBer for all we know, that might
explain things.
----- Original Message -----
From: Mitch Cox
To: Carl ; Tim Kass ; Charles Hedrick ; amps@contesting.com
Sent: Sunday, July 17, 2011 2:38 PM
Subject: Re: [Amps] Hunter 2000c Low Output.
During the past 35 years I have seen well over 100 Hunter amplifiers come in
and go out. Doesn't matter what's involved the gentleman explained his problem
well. It doesn't matter what is supposed, what matters is his problem which I
thought he explained well. Why not address the problem rather than to tell him
what is "supposed". If the initial voltage reading is inaccurate as to it's
number, it is still accurate to it's loss weather it is factory correct or not.
Where is your reasoning powers? I am just not as readily bullied as some that
have been here and I stand by what I said to start with which in the end will
prove to be correct as you will see in the end.
----- Original Message -----
From: Carl
To: Mitch Cox ; Tim Kass ; Charles Hedrick ; amps@contesting.com
Sent: Sunday, July 17, 2011 1:43 PM
Subject: Re: [Amps] Hunter 2000c Low Output.
Explain where you have seen 100 2000C's please?
As far as your other comments it shows poor troubleshooting logic to not
ascertain exactly what is involved. What if the voltage reading is simply
wrong?????
Lets get back to trying to help the OP and not start some silly chest
pounding using overblown graphics.
Carl
KM1H
----- Original Message -----
From: Mitch Cox
To: Carl ; Tim Kass ; Charles Hedrick ; amps@contesting.com
Sent: Sunday, July 17, 2011 12:28 PM
Subject: Re: [Amps] Hunter 2000c Low Output.
Regardless of what the correct plate voltage should be, he says his was
at 3400 volts and now that has fallen a considerable amount with output power
going down with it. This would seem to indicate one of two things, either the
primary main voltage has dropped or something has happened in the power supply
to cause the drop in voltage or loss in output. I addressed the problem, not
what it is supposed to be. I have seen a hundred of these amps and very few
have the factory parts in them as they started life so his first statement of
3400 volts could be absolutely correct. As far as heavy duty goes, I don't
think I could put any Hunter amp in that category.
----- Original Message -----
From: Carl
To: Tim Kass ; Charles Hedrick ; amps@contesting.com
Sent: Sunday, July 17, 2011 11:44 AM
Subject: Re: [Amps] Hunter 2000c Low Output.
That is the correct standby voltage and it should drop to 2200-2300
under
full load.
I dont understand why the Eimac 3-400Z should be a problem. It is a
little
harder to drive but otherwise a zero bias compatible tube. Ive swapped
them
as well as mixed in other 3-400Z amps.
Hunter claims either are permitted altho the Amperex is recommended
likely
since its a bit easier to drive.
The same with a 3-500 as it should run fine at zero bias at that
voltage
altho about 5.1V bias will improve the IMD about 6dB.
Carl
KM1H
----- Original Message -----
From: "Tim Kass" <k8wbl@yahoo.com>
To: "Charles Hedrick" <cchedrick@gmail.com>; <amps@contesting.com>;
"Mitch
Cox" <ww4cox@embarqmail.com>
Sent: Sunday, July 17, 2011 11:03 AM
Subject: Re: [Amps] Hunter 2000c Low Output.
I also have the wonderful Hunter 2000C amp... My standing voltage is
2700
VDC...same caps ... this amp has a diode block arrangement, very heavy
duty
parts. Make sure you are running the AUX LOAD in the 0 position on the
lower
bands and try it again it a dummy load on 40 meters to start. ALSO --
this
amp was designed for Amperex 8163 (3-400z) and mine ran well with the
original 8163's in it...however, I have tried several pairs of Eimac
3-400z
and it doesnt like (2) running together....very low output...300
watts..
take one of the tubes out and run it briefly as a single tube and see
what
output you get... I now run a single 3-500Z Eimac and does well..got
some
more coming to try to run a pair of them.. but if you amp runs fine on
the
single tube...you can then eliminate some of the other issues... high
SWR
input from solid state tubes doesnt seem to bother it to much but I
have an
IC-746PRO and use the internal tuner to balance things..but unless
the SWR is over 3:1 between the radio, the amp doesnt seem to mind...
I
also use the Heathkit AMPKEYER for good measure. Great amp, I have had
2 of
these..will never sell this one..
73, Tim K8WBL
--- On Sun, 7/17/11, Mitch Cox <ww4cox@embarqmail.com> wrote:
From: Mitch Cox <ww4cox@embarqmail.com>
Subject: Re: [Amps] Hunter 2000c Low Output.
To: "Charles Hedrick" <cchedrick@gmail.com>, amps@contesting.com
Date: Sunday, July 17, 2011, 12:30 AM
The first thing I would be looking for after first checking the
incoming AC
voltage would be an open rectifier or capacitor in the power supply
section.
But first you need to make sure that the incoming line voltage is where
it
should be. From the report of a bad match between the radio and amp you
almost would want to look in the bandswitch section of the tuned input
if
one exists but that would have no effect on the plate voltage.
----- Original Message -----
From: Charles Hedrick
To: amps@contesting.com
Sent: Saturday, July 16, 2011 10:11 PM
Subject: [Amps] Hunter 2000c Low Output.
HI All,
This has me puzzled. HV is 2800 down from 3400 which is normal in this
small town this time of year. I noticed yesterday that the power level
was
fluctuating weirdly up and down. when tuning the amp into the dummy
load.
So last night I installed new 3-500ZG's and cooked them for 24 hours. I
just tried the amp again and the power out is way down, the rig is
seeing a
high SWR. Bad Tubes....I just pulled a pair from the AL-82 and got the
same
results. I installed the new pair in the AL-82 and got 1300 key down
with
65 watts drive. The HV on the hunter doesn't fluctuate, and I'm .38 amp
and
300 output with HV dropping to 2400 at key down. The AL-82 is seeing the
same HV drop by the way, but handles it better, 85 watts drive is 1500
CW
with the new tubes. Parasitic Suppressors bad? Stumped here.
Thanks,
Cam
WA4JKW
NCS MMSN
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3769 - Release Date: 07/16/11
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3770 - Release Date: 07/17/11
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3770 - Release Date: 07/17/11
--------------------------------------------------------------------------
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3770 - Release Date: 07/17/11
----------------------------------------------------------------------------
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3770 - Release Date: 07/17/11
------------------------------------------------------------------------------
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1390 / Virus Database: 1516/3770 - Release Date: 07/17/11
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|