I know this sounds kind of stupid but a friend of mine had the same problem you
are describing. He had inadvertently hooked the input and output coax
connections on the back the wrong way. This nearly drove him crazy until he
realized what he had done.
----- Original Message -----
From: Larry
To: Amps
Sent: Sunday, October 31, 2010 7:02 PM
Subject: Re: [Amps] Clipperton L suggestion
I did solder that small wire. I have continuity from the B+ pad on power
supply
board to the plate caps. The small wire came wrapped on a terminal lug so
it was obvious I needed to do something with it.
I am sure I missing something simple that I did or didn't do. Just trying to
find it.
Didn't do much with the amp today as I was playing contest.
73, Larry W6NWS
----- Original Message -----
From: "Alek Petkovic" <vk6apk@bigpond.com>
To: "Larry" <w6nws@arrl.net>; "Amps" <amps@contesting.com>
Sent: Sunday, October 31, 2010 5:45 PM
Subject: Re: [Amps] Clipperton L suggestion
> G'day Larry
>
> That Ameritron plate choke comes with the wire at the top, tinned but not
> soldered. Make sure you didn't forget to solder it and make sure the
> soldered joint is sound.
>
> I put the same choke in my Clipperton L and only noticed that I hadn't
> soldered the wire during the final once over before putting the covers on.
>
> 73, Alek
>
>
> At 10:28 PM 31/10/2010, Larry wrote:
>>I have had this amp since the 1980's and never had trouble with the TR
>>relay
>>(well, other than it is slower than molasses). It was untouched in the
>>mods
>>I did.
>>But I did check continuity of the relay contacts. The TR relay does switch
>>over.
>>
>>I think, as Roger also suggested, perhaps the problem is in the bias
>>circuit. It too
>>is affected by the TR relay. I did not directly change the bias circuit
>>but
>>it was
>>affected in the sense that the filament RFC was changed and it is related
>>to
>>the
>>bias circuit (a 47K resistor and 50W zener). The RFC was connected to a
>>terminal
>>strip which I moved about an inch to fit the new RFC in and it looks OK
>>and
>>some
>>continuity checks seemed OK but I am going to do some additional checks to
>>make
>>sure I didn't mess up something. The RFC and terminal strip are in the
>>middle of the
>>amp and the relay, resistor, and zener are on the back panel of the amp.
>>
>>73, Larry W6NWS
>>----- Original Message -----
>>From: "Danny Pease" <dpease@adams.net>
>>To: <amps@contesting.com>
>>Sent: Sunday, October 31, 2010 9:10 AM
>>Subject: Re: [Amps] Clipperton L suggestion
>>
>>
>> > Larry, did you confirm continuity across the T/R relay contacts? When
>> > I
>> > had
>> > a Clipperton, that was an ongoing issue.
>> >
>> >
>> >
>> > NG9R
>> >
>> >
>> >
>> >
>> >
>> > Message: 2
>> > Date: Sat, 30 Oct 2010 23:34:20 -0400
>> > From: "Larry" <lknain@nc.rr.com>
>> > Subject: [Amps] Suggestions - I broke my amp
>> > To: "Amps" <amps@contesting.com>
>> > Message-ID: <6DE29DB55E8740479687855C81AF7535@LarryKnainPC>
>> > Content-Type: text/plain; charset="iso-8859-1"
>> >
>> > I am looking for suggestions regarding my Clipperton-L. The basic
>> > problem
>> > is
>> > that there is
>> > no output. No apparent plate current.
>> >
>> > I did several things:
>> >
>> > 1. I replaced the power supply board which seems to be working as the
>> > meter
>> > shows about
>> > 2500V (I don't have an HV probe to confirm independently that there is
>> > 2500V).
>> > 2. I had to fix the parasitic suppressors so I put in an AL572 RFC and
>> > suppressor board and
>> > increased the bypass cap to 0.001.
>> > 3. I changed the plate blocking cap to 2000pf (from 500pf) and changed
>> > a
>> > couple of doorknobs
>> > for 160. The no output has been checked only on 20 and 15 so far.
>> > 4. I changed the filament RFC to an RF Parts RFCFIL30.
>> >
>> > Some other facts:
>> >
>> > 1. The filaments are lit.
>> > 2. The meter shows what I recall as roughly the correct plate voltage.
>> > 3. Using an ohmmeter there is continuity from the PS HV pad to the
>> > plate
>> > connectors.
>> > 4. There is no plate current that I can see. Although, I once saw the
>> > plate
>> > current go to about
>> > 350mA and still no output.
>> > 5. Several years ago I added a tuned input board and there is
>> > continuity
>> > from the LVDC pad to
>> > input board and the bandswitch (unchanged in current mod but changed
>> > with
>> > the input board)
>> > still works correctly.
>> > 6. There is continuity from the plate to plate blocking capacitor and
>> > continuity from the "other"
>> > side of the plate blocking capacitor to the plate tuning capacitor.
>> > 7. I rechecked the connections and still think everything is correct.
>> > 8. No arcs, blown fuses, etc.
>> >
>> > I have obviously overlooked something. Suggestions?
>> >
>> > 73, Larry W6NWS
>> >
>> >
>> >
>> > _______________________________________________
>> > Amps mailing list
>> > Amps@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/amps
>> >
>>
>>
>>_______________________________________________
>>Amps mailing list
>>Amps@contesting.com
>>http://lists.contesting.com/mailman/listinfo/amps
>
>
> http://www.qrz.com/db/vk6apk
> http://www.qrz.com/db/vk6ap
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1153 / Virus Database: 424/3229 - Release Date: 10/31/10
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|