Amps
[Top] [All Lists]

Re: [Amps] which HV connector to use?]

To: <amps@contesting.com>, <ranchorobbo@gmail.com>
Subject: Re: [Amps] which HV connector to use?]
From: "Edward Swynar" <gswynar@durham.net>
Date: Fri, 15 Jan 2010 13:47:15 -0500
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Hi Rob,

Yes, as Alex correctly points-out, this topic HAS been round the oval at
least once before...! Hi Hi

...And as before, I *still* maintain that you can't do much better than to
employ good-quality (as in "made in the USA") PL-259's, SO-239's, & RG-8 /
RG-11 coaxial cable for your inter-equipment B+ wiring & connections...

Just remember to NEVER EVER leave the exposed centre pin of the
amplifier-side PL-259 , well, exposed!!! At least not while the p.s. is
activated, & the other end of the jumper cable might still be connected to
same...!

I've used the coax jumper route for some 33 years here now, & have not had
any issues. PERIOD. Best of all, the hardware is all commonly available,
too...

~73!~ de Eddy VE3CUI - VE3XZ


********************************



----- Original Message -----
From: <gswynar@webmail.durham.net>
To: <gswynar@durham.net>
Sent: Friday, January 15, 2010 1:40 PM
Subject: [Fwd: Re: [Amps] which HV connector to use?]


> ---------------------------- Original Message ----------------------------
> Subject: Re: [Amps] which HV connector to use?
> From:    "Rob Atkinson" <ranchorobbo@gmail.com>
> Date:    Fri, January 15, 2010 1:35 pm
> To:      "Alex Eban" <alexeban@gmail.com>
> Cc:      amps@contesting.com
> --------------------------------------------------------------------------
>
> okay guys thanks vy much.  I'm getting a better picture now on how to
> proceed.
>
> 73
>
> Rob
> K5UJ
>
> On Fri, Jan 15, 2010 at 9:46 AM, Alex Eban <alexeban@gmail.com> wrote:
> > Guys, we played around with this a while ago!
> > Use ignition wire - copper, NOT carbon core- and wire it point to point
> if you're afraid of connectors. It's rated to about 20 kV and easily
> handles 1 or 2 Amps.
> > Alex 4Z5KS
> >
> > -----Original Message-----
> > From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
> On Behalf Of Rob Atkinson
> > Sent: Thursday, January 14, 2010 11:32 PM
> > To: amps@contesting.com
> > Subject: Re: [Amps] which HV connector to use?
> >
> > I'm trying to get my head wrapped around all this.
> >
> > I am planning a h.v. supply homebrew project and have most of the parts
> (but every time I think that something like this comes up).
> >
> > I want to build a separate B+ supply for my Ten Tec Centurion amp. The
> idea is to have a supply that does not increase the voltage but
> increases the current capability and goes from ICAS to CCS. It's partly
> unnecessary I admit, but it started with good intention and also as a
> learning exercise (which it still is). The idea is to make the
> Centurion capable of handing high duty cycle modes and AM, but the power
> supply will also be useful for other future projects, supplying
> > 3.2 KV at 1.5 A CCS.
> >
> > I bought some h.v. wire and those millen plug/jack pairs from RF Parts a
> few months ago. Now it seems they're inadvisable. I admit the h.v.
> wire seems hard to work with, brittle and hard to strip. RG213 by
> comparison is a lot easier to work with. I'm getting the
> > impression I should go with that, hardwired into the amp cabinet with
> SHV connectors on the power supply cabinet. Or is this overkill for
> 3.2 KV?
> >
> > 73
> >
> > Rob
> > K5UJ
> > _______________________________________________
> > Amps mailing list
> > Amps@contesting.com
> > http://lists.contesting.com/mailman/listinfo/amps
> >
> >
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>


_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>