The table in the Eimac power grid tubes booklet shows the better figure for
the 3-5ooZ.
73
Peter
-----Original Message-----
From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
Behalf Of Hsu
Sent: Mittwoch, 21. Januar 2009 18:29
To: sccook1@cox.net
Cc: amps@contesting.com
Subject: Re: [Amps] 3-500zs to 8877
But 8877 have better 3rd IMD performance.Maybe longer tube life.
----- Original Message -----
From: <sccook1@cox.net>
Cc: <amps@contesting.com>
Sent: Thursday, January 22, 2009 1:21 AM
Subject: Re: [Amps] 3-500zs to 8877
> Pair of 3-500Z = $360
> Single 8877 = $#@*^&!
>
> -S
>
>
>
> ---- Hsu <hsu4qro@gmail.com> wrote:
>> 3CX1500D7 is better,
>> It use same socket as 3-500Z.
>> Hsu
>> ----- Original Message -----
>> From: "Val Erwin" <val.erwin@sbcglobal.net>
>> To: <amps@contesting.com>; "Donald Fox" <taurusshoguy@yahoo.com>
>> Sent: Wednesday, January 21, 2009 11:23 PM
>> Subject: Re: [Amps] 3-500zs to 8877
>>
>>
>> > Hi Donald:
>> >
>> > A good example of the change you would like to achieve is available by
viewing the Ameritron series of amps. Specifically, compare the AL-82 (2 X
3-500s) to the AL-1500 (single 8877).(You can download the manuals)
>> >
>> > Both amps use the same power suppply and the same chassis. Despite
owning an AL-1500, I have never explored what they do about the difference
in filament voltages between the two models.
>> >
>> > These two models of Ameitron amps run very high plate voltage as
compared to say a Heathkit SB-220 or a Henry etc.............This higher
plate voltage is really what is needed to make an 8877 "play".
>> >
>> > I am currently exploring a similar project: Placing an 8877 in an Alpha
78
>> >
>> > GL
>> >
>> > Val a.k.a. W5PUT
>> >
>> > --- On Wed, 1/21/09, Donald Fox <taurusshoguy@yahoo.com> wrote:
>> >
>> > From: Donald Fox <taurusshoguy@yahoo.com>
>> > Subject: [Amps] 3-500zs to 8877
>> > To: amps@contesting.com
>> > Date: Wednesday, January 21, 2009, 2:11 PM
>> >
>> > Gentlemen:
>> >
>> > Just submitting a quick poll to see what the feeling is about making
the swap
>> > from a pair of 3-500s to the almighty 8877.
>> >
>> > The donor is my very good condx Henry 2K Classic X which I do not want
to
>> > butcher. I am aware that the Henry consoles were oem equipped with the
8877 and
>> > other tubes.
>> >
>> > My goal is not for more power, but to enjoy the lower drive
requirement of
>> > the 8877 for my IC746.
>> >
>> > I know that the filament xformer and socket would need to change as
well as
>> > reworking the airflow for cooling.
>> >
>> > So, can the change be done without major mods to the input/output
networks??
>> >
>> > If not, then I will drop the idea and enjoy it as is. Changing to
another
>> > amplifier is not in the budget, and since I have a soft spot for the
80's
>> > model Henry consoles, this one is bound to be around as long as I can
afford it.
>> >
>> > Thanks for your comments pro or con in advance.
>> >
>> > Don N8ECH
>> >
>> >
>> > _______________________________________________
>> > Amps mailing list
>> > Amps@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/amps
>> >
>> > _______________________________________________
>> > Amps mailing list
>> > Amps@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/amps
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|