Gerd,
Have you created an override for the IC-706mkIIG CI-V address in
WriteLog? The CI-V address used when you select IC-706 is that
of the *original* IC-706 (48h) - not the 706mkII (4E) of the 706mkIIg
(58).
If you have an IC-706mkIIg, you must follow the information in the
[RIGS] section of the Writelog Help to set the address to 58h. If
you don't do that, you will need to change CI-V address in both the
radio and microHAM Router to 48h so Writelog can see it.
With an address override in WriteLog.ini, I run my 706mkIIg at 19200
bps without any problem.
Please refer to the Writelog documentation!
73,
... Joe, W4TV
On 6/14/2012 10:55 AM, Gerd Uhlig, DL7VOG wrote:
> Hello Joe,
> thank you very much for your reply on my question.
> I forgot to mention that I did exactly what in the support file is
> suggested.
> And I found out that I forgot to check <strict bps> in the DigiKeyer -
> now RTTY transmission is okay.
> But still no CAT communication between TX and WriteLog (frequency and mode)
>
>
> I programmed the DigiKeyer II as follows:
>
> CAT: COM4 (4800bps) open 4800 8N2 (the red arrow is blinking)
> FSK: COM6 PTT on
> CW: none
> PTT: none
> WinKey: COM3
>
> WriteLog setup:
>
> COM3 - CW - PTT YES
> COM4 - IC-706 - 4800 - PTT NO
>
> CW keyer type - K1EL Winkey
>
> Maybe something is wrong with the ini file.
>
> 73 - Gerd
>
>
>
>
> www.dl7vog.de
> www.qslnet.de/hk0gu
> www.qsl.net/vp2v-dl7vog
> www.qslnet.de/zf2gu
> www.qslnet.de/j3-dl7vog
> www.qslnet.de/c6aka
>
>
> Am 14.06.2012 12:15, schrieb Joe Subich, W4TV:
>> > The setup here is IC-706MK2G - DIGI KEYER II and WriteLog V. 11.04A.
>>
>> See the example configuration for Writelog and Digikeyer II available
>> via "Help | Download Documents" in microHAM Router or online from the
>> Digikeyer II area at www.microHAM-USA.com/Support.html.
>>
>> 73,
>>
>> ... Joe, W4TV
>>
>>
>>
>> On 6/14/2012 4:50 AM, Gerd Uhlig, DL7VOG wrote:
>>> First of all thank you for your hints. CW works fine now but there are
>>> still a few problems waiting to be solved.
>>>
>>> The setup here is IC-706MK2G - DIGI KEYER II and WriteLog V. 11.04A.
>>>
>>> The main problem at the moment is that WriteLog doesn't overtake the
>>> frequency from the transceiver, though DIGI Keyer changes QRG when the
>>> rigs tuning know is turned.
>>> When I open WriteLog the setup window of Digi Keyer still shows the
>>> right frequency but the red arrows at COM4 and WinKey (COM3) are
>>> blinking about once per second and after about 8 seconds the displayed
>>> frequency and mode above COM4 is greyed out for about 1 second and so
>>> on. When I close Writelog all is okay in the Digi Keyer setup.
>>>
>>> The left button beside the entry window in WriteLog shows< kHz CW>
>>> and
>>> when I open it the window shows nothing in the frequency window in the
>>> upper right position.
>>> Log the frequency of QSOs is set to<rig on COMM4>.
>>> All (rig, digi keyer and WriteLog) is set to 4800 bps.
>>> The second problem is RTTY - reception is okay but I can't transmit at
>>> all - but this is for a later solution.
>>>
>>> Does anybody have any suggestion to solve the problem?
>>>
>>> 73 de Gerd / DL7VOG
>>>
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|