In the clone window, select the TU Type drop-down and then select
MMTTY. A new MMTTY control panel should open, but it is tricky as it
will exactly overlay the current MMTTY control panel. You will need to
select it and move it out of the way.
You should then be able to select a different profile for each MMTTY
control panel.
My problem was after I did that and then closed Writelog, I received an
error that MMTTY.INI could not be updated. When I then re-opened
Writelog, MMTTY could not communicate with the outside world. After
again closing Writelog and then directly invoking MMTTY, I find that the
FSK and Control ports have been reset to NONE.
It acts like whatever caused the MMTTY.INI update error is causing the
MMTTY FSK and control ports to be reset. Once that happens, you have to
use MMTTY to configure them again.
This works for Ed so I am assuming I have a configuration error. I will
be curious to see how successful you are.
Dick
--
Dick Flanagan K7VC
dick@k7vc.com
On 1/5/2012 10:44 PM, Gary AL9A wrote:
> Ed,
>
> I can get the clone RittyRite window to open, but it didn't ask me for the
> path to MMTTY. Despite this it appears to be receiving and decoding. But
> per Dick's request how do you get another MMTTY window to function with the
> clone window so that you can choose a different Profile for the clone?
>
> 73,
> Gary AL9A
>
>
> ----- Original Message -----
> From: "Ed Muns"<w0yk@msn.com>
> To: "'Dick Flanagan'"<dick@k7vc.com>
> Cc: "'WriteLog'"<writelog@contesting.com>
> Sent: January 05, 2012 2:41 PM
> Subject: Re: [WriteLog] WL/MMTTY Problem
>
>
>> Ah, so, but you don't need two instances of MMTTY. You just "clone" the
>> first Rttyrite window that has MMTTY as the TNC. In the Rttyrite File
>> menu
>> of the first Rttyrite/MMTTY window you bring up, click 'Clone' and when it
>> asks you for the path to MMTTY, give it the path to the first instance of
>> MMTTY. You can have any number of clones without resorting to additional
>> instances of MMTTY.
>>
>> Ed - P49X (W0YK)
>>
>> Dick, K7YC, replied:
>>> As per your NCCC presentation, I am looking for the opportunity to have
>>> two different profiles processing the same audio stream.
>>>
>>> Dick
>>>
>>> --
>>> Dick Flanagan K7VC
>>> dick@k7vc.com
>>>
>>>
>>> On 1/5/2012 3:20 PM, Ed Muns wrote:
>>>> I've had this happen once in a while, but not often, and not recently.
>>> I've
>>>> never worried about it or looked into it. But, I am curious about what
>>> is
>>>> going on.
>>>>
>>>> Why are you using two instances of MMTTY?
>>>>
>>>> Ed - P49X (W0YK)
>>>>
>>>> Dick, K7VC, wrote:
>>>>> During today's RTTY RU practice, I noticed a problem running two
>>>>> instances of MMTTY. When exiting WL I received an error message that
>>>>> MMTTY.INI cannot be updated. When I again invoke MMTTY, all port
>>>>> settings have been set to NONE.
>>>>>
>>>>> Why is WL trying to update MMTTY.INI? What kind of circumstance would
>>>>> cause this kind of error? WRITELOG.INI has the correct path to the
>>>>> MMTTY directory and MMTTY operates properly until I exit WL at which
>>>>> point the MMTTY ports are set to NONE and I need to reset them.
>>>>>
>>>>> Could the two instances of MMTTY be fighting over some resource?
>>>>> Could
>>>>> one instance be trying to update MMTTY.INI while the other instance
>>>>> has
>>>>> it open? Has anyone else experienced difficulties running two
>>> instances
>>>>> of MMTTY from within WL?
>>>>
>>>>
>>>>
>>>>
>>>>
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web: http://www.writelog.com/
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
>
>
>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|