: [TowerTalk] Need house mount brackets for 1.75"-2" OD mast
Sender: owner-towertalk@contesting.com
Received: from dayton.akorn.net ([205.217.100.11] (may be forged))
by arl-img-1.compuserve.com (8.8.6/8.8.6/2.10) with ESMTP id
KAA27812;
Wed, 28 Jan 1998 10:37:25 -0500 (EST)
Received: from dayton.akorn.net (dayton.akorn.net [205.217.100.11])
by dayton.akorn.net (8.8.5/8.8.5) with SMTP id KAA16778;
Wed, 28 Jan 1998 10:37:22 -0500 (EST)
Received: by dayton.akorn.net (TLB v0.10a (1.23 tibbs 1997/01/09
00:29:32)); Wed, 28 Jan 1998 10:37:15 -0500 (EST)
Message-Id: <1.5.4.32.19980128153937.00689f14@southwind.net>
X-Sender: k0wa@southwind.net
X-Mailer: Windows Eudora Light Version 1.5.4 (32)
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
To: <towertalk@contesting.com>
Date: Wed, 28 Jan 1998 09:39:37 -0600
To: Jim Reisert <ad1c@contesting.com>
From: Lee Buller <k0wa@southwind.net>
Subject: Re: [TowerTalk] Need house mount brackets for 1.75"-2" OD mast
Cc: towertalk@contesting.com
Sender: owner-towertalk@contesting.com
Precedence: bulk
X-List-Info: http://www.contesting.com/towertalkfaq.html
X-Sponsor: W4AN, KM3T, N5KO & AD1C
At 10:24 AM 1/28/98 -0500, you wrote:
>I want to mount an R7 vertical onto the back of my shed using house
>mount brackets. I have a 1.75" OD mast that I will be using as the
>base. I looked at the Radio Shack brackets, that the catalog says
>will take 1.75" OD mast, but they certainly don't, way too small.
>
>Where can I find good set of house mount brackets that will accomodate
>1.75" to 2" OD mast? I'd prefer "checkbook engineering" [(c) K1VR] on
>this one.
>
>Thanks - Jim Reisert AD1C
>AD1C@contesting.com
Screw in a a 2x4 about 2 foot wide to the house...then use Plumbers Tape to
mount the mast to the 2x4. Use lag screws on the plumbers tape. Make
sure
you secure the bottom. I usually use a red brick with a holes...drive a
pipe in the ground at the bottom about two feet down and slip the mast over
the pipe.
Won-t move for years.
Lee
k0wa@southwind.net
One more idea to add top this one. If you can find conduit or water pipe u
clamps fo the correct size to fit the mast, they cna be used to attach to
the 2x4 or house if its flat. I have done this to mount 1 meter DBS
satellite dishes to side walls. If the mast rotates in the clamps, you cna
drill thru and add a screw to pin them together. 73 Jim KI7Y
--
FAQ on WWW: http://www.contesting.com/towertalkfaq.html
Submissions: towertalk@contesting.com
Administrative requests: towertalk-REQUEST@contesting.com
Problems: owner-towertalk@contesting.com
Search: http://www.contesting.com/km9p/search
|