When you look at an N connector, specifically the center pin - remember that
the N connector center pin is the same as the center pin of a BNC connector.
W6NL asked me this question - would you run 1500 watts with BNC connectors?
73
Tim K3LR
(Only 7-16 DIN and TONS of "quality" UHF connectors at this station
TIGHT PL-259s work GREAT - tighten up)
-----Original Message-----
From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of Mike
Waters
Sent: Friday, December 07, 2018 8:57 PM
To: Frank Donovan; topband; Steve Maki
Subject: Re: Topband: Rather use N-type (was Re: The answer to PL-259
Thank you, Frank and Steve! I just learned something useful. :-)
I bought these N plugs in the early 1980s from Nemal Electronics. Perhaps
what you are describing was not available then? (That's a rhetorical
question. ;-)
If I ever get back on VHF/UHF, I'll get those.
73, Mike
www.w0btu.com
On Fri, Dec 7, 2018 at 7:26 PM <donovanf@starpower.net> wrote:
> Hi Mike,
>
> Captivated pin N connectors for hardline coax fits tightly over
> the center conductor.
>
> Captivated pin N connectors for flexible coax typically has a
> pin that requires solder.
>
> Floating pin N connectors belong in the trash bin.
>
> 73
> Frank
> W3LPL
>
> ------------------------------
> *From: *"Mike Waters" <mikewate@gmail.com>
> *To: *lists@oakcom.org
> *Cc: *"topband" <topband@contesting.com>
> *Sent: *Saturday, December 8, 2018 12:10:38 AM
> *Subject: *Re: Topband: Rather use N-type (was Re: The answer to PL-259
>
> The one I have in my hand has a solder hole in it. I take it that there
are
> newer ones that have contacts that grip the coax center conductor?
>
> 73, Mike
> www.w0btu.com
>
> On Fri, Dec 7, 2018 at 6:04 PM Steve Maki <lists@oakcom.org> wrote:
>
> > Well here's the advantage of captivated center pins: the pin is NOT
> > bonded to the center conductor. IOW, if the coax center conductor
> > shrinks a bit, it can slide in the center pin and the pin stays put.
> >
> > And that's exactly what you want it to do - especially with an N
> connector.
> >
> > -Steve K8LX
> >
> >
> > On 12/07/18 14:25 PM, Mike Waters wrote:
> >
> > > Exactly my experience, even with captivated pins!! And my coax runs
> were
> > > only about 100' long.
> > >
> > > The captivating washers were made of TeflonR, *and Teflon cold flows*.
> > This
> > > was when I lived in Toledo, Ohio when the temperature dropped well
> below
> > > zero.
> > >
> > > Four photos of those N connectors are at
> > > http://www.w0btu.com/files/misc/N_plugs . See the last two.
> >
> > > On Fri, Dec 7, 2018, 1:02 PM Richard (Rick) Karlquist <
> > richard@karlquist.com>
> > > wrote:
> > >
> > >> My two 500 foot RG-216 military surplus cables both eventually
> exhibited
> > >> retracted pins on the type N connectors at both ends. I replaced
them
> > with
> > >> PL-259's. ... Success anecdotes about install once and never touch
> > again
> > >> commercial sites are probably not relevant to ham applications.
> >
> > _________________
> > Searchable Archives: http://www.contesting.com/_topband - Topband
> > Reflector
> >
> _________________
> Searchable Archives: http://www.contesting.com/_topband - Topband
> Reflector
>
>
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
|