Felix, I just looked in Tashijian ( Used to be called Tri-Ex ) Tower Catalog and they show a WT-51 tower and it is rated for 13 Sq Ft antenna for 85 mPh wind gust for 3 seconds So you need to look at
Can anyone tell me why a wire rope cable would tend to crush itself in the layers on the center hub of a winch ? I purchased the wire rope at a Marine rigging company in San Diego as the cheezy cable
Jim, Bingo! you hit the nail on the head.... Coincidently, just before reading your mail, had just gotten off the phone with a tech guy named Bruce at Dutton Lainson<http://www.nextag.com/norob/Ptitl
You can get 8 Pin Molded Rubber Connectors here *http://tinyurl.com/8-Pin-Molded-Connector Click on *Molded Trailer Connectors<http://www.wiringproducts.com/contents/en-us/d174.html> at top of page T
Darl, Easy to replace - just remove top cover It uses a type 1819 and if U neber want to have to replace the bulbs again this advice from K6EL in a previous post You may want to replace it with a dir
I am posting this for a ham friend U.S. Tower model TX455 55 foot free standing crankup tower. CX3 coax arms. TB2US 2 hole thrust bearing. TRX80 Raising fixture. M10 10 ft mast. Hygain TH11DXS 5 band
Wonder if anyone has used Jet Brand hand Winches Specifically the 2000N and 3000N models http://industrial.jettools.com/Results.aspx?cat=332926 They are typically specified for Horizontal Pull but I
I recently acquired a NEW Force 12 EF-240 2 El 40 mtr Yagi. ( New Old Stock - Several Years old ) If I understood the instructions correctly, when one is adjusting the antenna, one first tunes the Re
Wondering what the consensus is for the grease to be used for the bearings at each end of the rum on a LM-470D motorized crank up that has the Zerk Grease fittings and also for the TB-@ or 3 ( Not su
I have a Ham IV control box with the Idiom Press EZ-Rotor kit installed and it works great to automatically delay the brake release and other great features. I am about to install another EZ-Rotor bo
Just picked up a NEW Fulton KW3000 Worm Gear Style Winch today which I plan to use with a 1/2 inch variable or low speed Drill motor to tilt a LM-470D tower that has around 1300 lBs dead weight on th
Yeah I already thought of that and actually use a 2000 lB rated come along as I don't happen to have a few hundred pounds of weight around and also I wonder how much weight the tilt structure is rate
Page 9 at http://ky6la.com/n6kimonstir/index.htm shows the external view of the tower interconnection box I fabricated I took the original PVC piece of junque that Steppir sent and the junque connect
Thanks for info After agonizing over many Spur and Worm gear winch details and even considering a JET 2000N for $750 ( moment of insanity ! ) I decided on the *Fulton KW3000* and a powerful half inch
...and remember to remove Power from the control unit if you have the older type box pictured at the web site oix link I just sent ( I do not know about the newer control unit ) as power is still rou
Well, I got to thinking that teh Molwaukee Hoel Hog at 300 RPM would be too fast for the tower tilting application and thinking about wjat an appropriate RPM would be I come up with 90 to 120 RPM - S
Dave, Save yourself a lot of time in "Computer Hell" and get another laptop that has WIN98SE on it ( or one U can install WIN98SE ) They are very cheap - $50 to $100 at most for one that has CD Reade
Anyone use these when doing wire antenna repair or mods They seem to hold up very nicely ( strong ) and keep corroision off your connection Wondering if anyone has a cheaper source ir something that
A 3 section U.S. Tower Tubular type would be MA-550 with tilt fixture A Triangular Tri-ex ( Now Tashijian ) W-51 with tilt fixture would also work ( 3 section ) Both of those crank down to 22 FT or s