Evening, After SSB SS with the Orion and real antennas for once, I found myself with the BW on 1700-1900 most of the time. I have an Omni 6+ with the 1.8 kHz filter that does not see much use, so I w
Now would be a good time to ask about a firmware update??? Ha Ha, Robb _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/li
Thanks for all the input, will give it a try over the Holiday break. 73, Robb NØRU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contes
Leonard, When the front panel reads "Off:H", it means that the DSP NB is "OFF" but the Hardware blanker is still active. If you press and hold the NB button for several seconds, both the OFF and the
Joe, You have not missed anything, but still waiting for a release. Maybe it will coincide with the two year anniversary of the last one. Gave up on the last Version 2 and went back to 1.372. 73, Rob
Rick, Not that long...terminate the update, cycle power and start over. Took three tries on 2.063 for mine to load. GL, Robb NØRU _______________________________________________ TenTec mailing list T
Well at least MFJ did'nt buy them out! Robb NØRU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Since this is way off topic; Honda does not make a truck, Google Chevy/GMC, Ford, or Dodge to see trucks. Now, back to Ten Tec related topics. Robb NØRU ______________________________________________
This is normal, no more "tick marks" or user selectable sweep range. You will also notice that the S-meter will hang at the last reading as you spin the knob. But I find that the NR is working again,
How about "Paperweights" or "Door stops"? I have an Omni 6+, original owner and just hope not to have the dreaded Logic board failure. But along with my B/C-line and TR-7 Drakes, the Ten Tec's just k
Wrong reflector, try the one dedicated to Elecraft. Robb NØRU When does the KPA 500 become AVAILABLE ??? _______________________________________________ TenTec mailing list TenTec@contesting.com http
Hello, You will not need the 318 with the TS-590 as it has sufficient delay to prevent hot switching during CW. Now if you desire to run full break in on the TS-590, it may cause issues. In that case
Rick, I have not noticed this issue with my Orion. Your earlier email mentioned slow port response also, tried both N1MM and N3FJP with what appears to be normal operation. I use a Micro Ham USB 7.7.
Good afternoon, Decided to sell my TT Orion. Has the Auto tuner, 1.8, 500, and 250 Hz filters. Stock 1 kHz filter replaced with the Inrad 600 Hz filter. Purchased in 2005 from TT and Version 2 FW upd
Lee, You are thinking of the old 444 solid state amp. The 411 Centaur uses 3x 811A tubes. TT states on their website that they can no longer repair the 444. Concerning the history of the 422..the ori
Hello, I have 2 Ten Tec filters for sale: Model 217 500 Hz and the Model 219 250 Hz. $ 70 each shipped. Also have a DB37-TT-OR cable for the MicroHam Micro keyer to Orion interface. $45 shipped. USPS
Hello, I have a Ten Tec filter for sale: Model 217 500 Hz $ 65 shipped. USPS money order, no Pay Pal, or overseas shipping. Thanks, Robb N0RU Woodland Park, CO rurie@mywdo.com _______________________
Scott, It would work in the Orion, but there really is no advantage to using it since there is the Inrad 600 Hz filter that replaced the original 1kHz. There was some discussion several years back on
All, Sorry for the reply that went to the entire group rather than the intended person. Robb N0RU _______________________________________________ TenTec mailing list TenTec@contesting.com http://list