Boys and girls, any 9 volt ni-cad will work. harbor freight, about $2 each.. mike, wb8vgre _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.conte
Well now, I'm not too sure about that. without looking at the schematic, but I'd guess that this RAM/ROM/RTC has some sort of firmware installed at the Ten Tec factory. It's this firmware that gives
I am going to take a stab at this but I'll admit I've need had my fingers in one. First I'd see in in fact your drawing enough current to light the IV lamp. If you are, then place a AM broadcast rece
Guys, working on a Omni V. All back together and receiving and transmitting just fine. However, the display is off, just a tad, and I can't find anyplace in the manual on how to correct the error MID
Okay, i have one of the chips, took it out, but can replace it. however, i'd guess that the chip has to be left in the rig after the corrections? mike wb8vge On Oct 21, 2012, at 12:30 PM, Carl Moresc
I'd put my money on the 2.4khz filter. I worked in a paragon that sounded okay but rf power dropped off as you went higher in freq. at 10meters only 10-15 watts of power. Turned out to be a bad filte
vic, I don't have the paragon manual in front of me, so, doing this from memory. on 40 and 30 meters, the same relays control the L/C components so, if it is a relay problem, you should see it on 30
Bobby, the relays are made by US relay, They have a website, but it's confusing as hell. They say they take small orders, but there's no way to order. Digikey stocks some, but not the ones i needed f
I'd guess that it's all about the looks. I have a few Omni Vs, Omni VI's, corsairs and such with the associated accessories and while either one, black or gray, amp produce the same amount of power,
Well gang, another year is coming to an end. Need a few projects for the new year. That being said, I'd like a Triton four. Analog or digital would be fine. Broke would be even better. But... no extr
Gang... I've made a bit of progress cleaning out some small parts of the shack. Neatness is a sickness of the mind you know.... here's the link. It's just a FTP folder with images in it. Nothing fanc
Rick and all, I had one once, and like a dummy, I sold it. I keep looking but refuse to spend $800 on one. And like that same dummy, I sold my Argonaut II sometime ago. Bad idea. I was one of the bet
Naw, just ran out of space, that's all. There's heathkit and ten tec radios in the garage, the barn and upstairs in the living room. I know when I'm lying on that cold marble slab getting cotton stuf
Elecraft sells a small signal generator, single band( they have several models) and don't cost a fortune. About $40 or so. They produce a 50 mV or 1 mV signal on crystal controlled frequencies. Plug
It worth a try but the rec/transceive switch won't fix the rx problem. Mike wb8vge Sent from my iPhone _______________________________________________ TenTec mailing list TenTec@contesting.com http:/
randy, it is also possible that the regulator is not working and CAUSING the scr to trip. can you measure output voltage? or is zero indicating a shorted output line is the 20 amp fuse popped? It sho
Pete, did you follow the adjustment procedure in the manual? the ALC is set by both the front panel control and ALC trimmer on the LLdriver. Mike _______________________________________________ TenTe
Just an FYI A lot of VOM meters, when reading ohms, have the polarity of the test leads backwards. Mike wb8vge Sent from my iPhone _______________________________________________ TenTec mailing list
I remember going to Martin sound to buy parts and asking for 20 puff capacitors. He knew what I wanted Mike wb8vge Sent from my iPhone _______________________________________________ TenTec mailing l
I wonder if an adjustable coil could be found that would allow one to change and peak the sidetone freq as needed. While the pitch control still works, the L-C components are locked. Mike wb8vge Sent