Use at least 3 digits when you set RIT. Use *RMR050Cr for 50 hertz of RIT. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec ma
The internal BFO frequency adjustment for LSB is off 250 hertz. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list
They use a very fast reed relay for QSK switching/ Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list TenTec@contes
The N4PY program sets the baud rate itself, so that is not an issue. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing
The baud rate is not an option with any of the tentec radios. The N4PY program always sets the correct rate. You were using a kenwood radio last week which does have baud rate settings in the N4PY pr
Hi Barry, I know this won't help, but my memory tells me the filter was the same socket size and the filter was only a 4 pole filter. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.co
The real question is is the filter 200 hertz off or is your impression of the same tone 200 hertz off. Only the 250 filter would be narrow enough for this to show up. You need a second radio to see i
The Omni VI has a 9 mhz IF. It would need a hardware mod to bring the 9 mhz IF out to LPPan. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________
My N4PY Orion software will do this operation and use either PowerSDR-IF for the panadapter or TRX-Pan for the panadapter. You will also need the Telespost LP-Pan device to convert the 9 mhz IF outpu
I have just a few more comments on this. First, I have several users running the Orion with the 9 mhz IF mod, LP-Pan, and TRX-Pan. This works quite well and is very stable. Second, I also have an int
The Flex 1500 might be a better way to go then if sharing antennas. There's no hash with that one and still no sound card required or 9 mhz IF mod required. Carl Moreschi N4PY 121 Little Bell Dr. Hay
My N4PY software has full CW keyboard support for both these radios. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing
My software can still be run and control can still be done entirely form the radio. In this way, just the CW keyboard of my software can be used. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635
But you cannot do this with the Omni VII or Orion or Orion II. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list T
A tenth of an amp is all it takes to kill. But it takes volts to make the push to make the amps. In some scenarios, it is possible for 120 volts to cause the tenth of an amp to flow to kill. Carl Mor
That sounds like you have a non-stereo plug in the Key jack. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list Ten
Let us know how you make out with Nationwide. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list TenTec@contesting.
Another thing to remember to disconnect when a storm is coming is the phone line. I draw an imaginary circle around all my stuff on the operating bench and disconnect everything that crosses that lin
Let me caution about grounding. Unless your ground is a very good one, connecting your disconnected coaxes to ground may be actually connecting them to the lightning source directly. You must have an
I have been using an Astron 35M for my main supply since 1987. It has been on constantly since then except for when I shut things down for storms. The supply has never had any RFI problems and has pe