Dan Unless you have a direct reason to do otherwise only one route is necessary. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@d
Jim A Prism 2.5 card in TC mode in slot 1 and a Orinoco Silver in slot 2 in 802.11b mode will work. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847
Nate Bridging should not be turned on with NAT/DHCP also "Internal Radio IP" not sure what this is, If this is the units IP it should be set to the public ip address for things to work properly. Sinc
Nate If you want send me a copy of the cfg I will take a quick look (Make sure if you zip it if you do) Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908
Travis, When you unplug the inet connection, of course, the traffic will be limited to TCP requests coming from the clients so this could be a problem with how the traffic coming into the network, IP
FYI Someone ask if the Orinoco Version of TurboCell supports the Prism 2/2.5 chipset. We found out today 100% the answer is no. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cel
The only time I have seen this is where bridging AND NAT is turned on at the same time. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email:
Leszek Our cards work with Karlnet but Prism will only work in TurboCell mode at this point. Cisco is a proprietary solutions that KN does not support. http://www.demarctech.com/products/relia-wave-1
FYI, this is a link test using the new 100mW Prism 2.5 chipsets, as you can see from the screen capture the signal readings are what they should be. The incorrect signal readings, from the test we ha
Hmm interesting paper don't the graphics look familiar.. Charles you should give credit to the original author of this paper.. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell
Charles There is a big difference between reusing a white paper, without noting the proper author, and using documentation/software licensed, from the manufacture, with expressed permission for use a
Jim I am very sorry you are 100% correct my apologies to the list members.. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarc
This was not my point, a white paper is a published educational document, this one just happen to be by a competing product manufacture publishing as your own. I am sorry for being blunt but this rea
Bill I received word on this the other day, its still under development. No update on when it will be available. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170
If you give them everything technically they can control how much bandwidth they receive plus gain access to info about your network. Does not seem like a good idea, would not recommend this to my cu
Bill Take a look at the docs on our site (http://www.demarctech.com/downloads/demarc-turbocell-manual.pdf) "1.1.5 - Max Tx Rate KBits/Sec If you wish to limit the maximum data transmit rate for a par
Nate Demarc has a solutions but more geared towards the AP side of the install: http://www.demarctech.com/products/relia-wave-dt-ese-200-sbc.html This works with TC/SEC is POE ready and works great w
Jim The pubic address should be set to the public address you want NAT to translate to. If you only have one public then yes. Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell:
Jim Are you using an I from the NAT ip space on your system? Sincerely Tony Morella Demarc Technology Group Office: 908-996-7995 Cell: 908-246-9170 Fax: 908-847-0202 email: tony@demarctech.com http:/