[Skimmertalk] Skimmertalk Digest, Vol 108, Issue 8

Paul F. Merrill marinesvcs at gmail.com
Sun Nov 19 12:03:46 EST 2017


If he's not on here, I'd hit up Jim, K9YC. He's the local authority on
chokes (and lots of other stuff.)

On Sun, Nov 19, 2017 at 09:00 <skimmertalk-request at contesting.com> wrote:

> Send Skimmertalk mailing list submissions to
>         skimmertalk at contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
>         http://dayton.contesting.com/mailman/listinfo/skimmertalk
> or, via email, send a message with subject or body 'help' to
>         skimmertalk-request at contesting.com
>
> You can reach the person managing the list at
>         skimmertalk-owner at contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Skimmertalk digest..."
>
>
> Today's Topics:
>
>    1. Re: I'm trying to build a common mode choke for 2, 200 and
>       630 meters and don't know what I'm doing (Wes Cosand)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 18 Nov 2017 18:42:50 -0500
> From: Wes Cosand <wes.cosand at gmail.com>
> To: RBN-OPS at yahoogroups.com, skimmertalk <skimmertalk at contesting.com>
> Subject: Re: [Skimmertalk] I'm trying to build a common mode choke for
>         2, 200 and 630 meters and don't know what I'm doing
> Message-ID:
>         <CAEZgdkZm2nibeCgmR52JQPiVSPyQ3yA4Dw_=
> 5Tca0de5LZi-Ng at mail.gmail.com>
> Content-Type: text/plain; charset="UTF-8"
>
> Let's try this a third time
>
>  I need some help.
>
>
>
> Jack Smith, K8ZOA (SK), wrote an impressive web page some years ago
> describing how he improved the performance of his active vertical antenna
> using chokes at both ends of the coax.
>
> https://web.archive.org/web/20150803213958/http://www.clifto
> nlaboratories.com/vlf_signals_with_improved_setup.htm
> <
> https://web.archive.org/web/20150803213958/http:/www.cliftonlaboratories.com/vlf_signals_with_improved_setup.htm
> >
>
>
>
>  I am trying to replicate that although using a different active antenna.
> But it isn't trivial to find toroids that provide much impedance at
> 100kHz.  It is my understanding that the most appropriate easily available
> Fair-Rite mix is their type "75".
>
>
>
> I bought 25 Fair-Rite 5975001801 toroids from Mouser.  They have an
> internal diameter of only 0.54 inches so I bought some RG-174-U planning to
> use about a dozen toroids at each end of the cable.  But I was surprised
> how few turns I could get through a stack of toroids, especially if I wound
> them in reasonably tightly.  Here is a photo of my attempt:
>
> https://photos.app.goo.gl/zeRaPbKiDViWIvJj2
>
>
> This toroid has an A of 3,025 nH.   Using the formulas in
>
> http://ka7oei.blogspot.com/2017/11/a-semi-typical-suburban-e-field-whip.html
> I calculate something like an impedance of 6900 ohms for these 25 toroids
> at 100 khz.
>
> Mouser stocks a type 75 toroid with an internal diameter of 1.4 inches with
> an A of 6850.
>
> How do I do this better?  Even putting a crimp BNC on coax is a new
> experience for me and I am feeling incompetent.  When I put this assembly
> on the receiver end of the coax before the coax power supply I observe very
> little obvious difference in the noise level at 136 kHz in HDSDR.  Is that
> expecting too much?
>
> Am I "straining at gnats and swallowing camels"?
>
>
>
> Wes WZ7I
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> Skimmertalk mailing list
> Skimmertalk at contesting.com
> http://dayton.contesting.com/mailman/listinfo/skimmertalk
>
>
> ------------------------------
>
> End of Skimmertalk Digest, Vol 108, Issue 8
> *******************************************
>


More information about the Skimmertalk mailing list