Glad to contribute to the cause Barry. Looks like the reflector squeezed the
text all together. It's easier to read if you click on the original post.
By the way, it has been over 6 years and that problem never reared its ugly
head again.
Later, Joe, K8MP
-----Original Message-----
From: Barry N1EU <barry.n1eu@gmail.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Thu, Nov 12, 2015 8:32 am
Subject: Re: [TenTec] Ten tec omni 6+ (5 mhz PLL board)
Thanks Joe, very helpful troubleshooting info for my favorite radio of all
time!
73, Barry N1EU
On Thu, Nov 12, 2015 at 8:03 AM, Joe Papworth via TenTec <
tentec@contesting.com> wrote:
> Hi Mike,
> Here's my final synopsis. There's more here than you'll probably ever
need
> to know. By the way, the info is also on the reflector from back in '09
> when I had the problem.?
> http://lists.contesting.com/archives//html/TenTec/2009-10/msg00238.html
>
>
> I suggest you compare my symptoms to what you're rig is doing and
> if it's the same (or very similar), just go for the?jugular and hit ALL
> the connections on the 5 mhz PLL board.?
>
>
> Later, Joe
>
>
> Radio Dudes: I figured I'd give you a final (I hope) synopsis on the
> PLL/Synthesizer problems I dealt with recently. The info may come in
handy
> for someone, some day. By the way, thanks to those who steered me
towards
> the PLL board. Otherwise, my radio might still be broken. (or in
> Sevierville) Symptoms:The display reads correctly. It even changes when
you
> turn the VFO. However, the received freq doesn't change. How did I know
> that? When I changed bands to 160, I could hear an AM broadcast
station.
> Turning the VFO didn't change what I was hearing. Fixing it:It was
> suggested that I check the 5 to 5.5 Mhz output from the PLL. I didn't
have
> a freq counter, so I used a Tektronix 456B, which is a 200 Mhz scope.
The
> output showed as 5.8 Mhz and it did not change when cranking the VFO or
> hitting the up/down buttons. The 2 inputs to the board (10 Mhz clock
and
> serial freq data) appeared to be good, so I was pretty sure I was on
the
> right track. NOTE: The output also h
> ad what seemed like a low voltage level (1 volt p/p). I called Ten Tec
> about the sig level, but they didn't know what it should be. (More on
that
> later) Another Ham who had PLL board problems strongly suggested that I
> re-heat suspect connections on the board. I did this (in fact, I hit
every
> connection on the board) and the radio worked for 2 days. While it was
in
> the working state, I scoped the PLL output and saw it change with the
> up/down buttons. The voltage level was 1 volt p/p in the working state,
so
> I now knew that was correct. For the next few days, the radio would work
> then not work. I tried to "make it fail" with heat and cold, but those
> didn't seem to make a difference. During this process, I made a few
notes
> and drawings of various waveforms and levels around the board.
> Unfortunately, 3 weeks have passed and some of those notes don't make
any
> sense to me now. Here are the ones that do: 1) At the junction labeled
> "Test point" (duh...go figure) on the P
> LL schematic: When working, and the rig set to 40 meters, it had a 100
> mv sine wave riding on a 325 mv DC level. (I forgot to record the
> freq). When failing, it was nearly at ground potential (less than 15
mv),
> with no sine wave. 2) At U4, pin 5, with the rig working, I saw 775 mv
when
> on 40 meters. I didn't record it in a failed state. 3) At R11 and R12,
> with the rig working: You should see a 5 volt level, with negative-going
> spikes to ground, every 100 usec. 4) U5, pin 6, with the rig working: 133
> Mhz signal. I can't remember if it was square or sine. 5) U4, pin 7,
with
> the rig working: 2 v DC 6) U4, pin 1, with the rig working: 3.5 v DC
> "Sometimes it's better to be lucky than good" While beating on components
> to try make it work, I noticed that a slight tap on L12 could make the
rig
> fail or work. I re-heated the connections to L12, (including L12's case
to
> ground on top of the board) and the radio has been fine since. That was
> over 2 weeks ago. I even got brav
> e enough to put it all back together several days ago and it's still
> working. Hopefully, it's been put to bed. Later, Joe
>
>
> -----Original Message-----
> From: Mike <w4mjr@att.net>
> To: k8mp <k8mp@aol.com>
> Sent: Wed, Nov 11, 2015 8:48 pm
> Subject: Re: Ten tec omni 6+
>
> OK Joe that would be great. I like my 564 and miss it when not in use.
I
> moved the Hercules II over to my ICOM 751A for the time being.? Ok Joe
look
> forward to your repair info. Thanks agn. Mike W4MJR
> Sent from my ALCATEL ONETOUCH A564C
> On Nov 11, 2015 7:33 PM, k8mp@aol.com wrote: You jogged my brain and
> yes, that was me Mike. I fixed it myself with help from the guys on the
Ten
> Tec reflector.
> It involved removing one of the boards (PLL board, think) and
> re-heating EVERY connection (top and bottom) with an iron (and add new
> solder if necessary)
>
> I'll look over my notes and get back to you with the details,
> probably tomorrow.
> Later, Joe
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Mike <w4mjr@att.net>
> To: k8mp <k8mp@aol.com>
> Sent: Wed, Nov 11, 2015 07:36 PM
> Subject: Re: Ten tec omni 6+
>
>
> 602606e" Sorry Joe but I might have you mixed up for
> someone else. I have a ten tec omni 6 plus and started losing audio
sound.
> It would come back in and then go back out. I could put it on the 160
meter
> band and hear an AM station but could not make it out what they were
> saying.? I replaced the 3 volt battery backup and did a reset but nothing
> changed. Anyway Joe I have been reading so much about trying to figure
out
> what was wrong before I send it in to ten tec for repair.? Anyway I
thought
> I had read on the contesting.com about you and your omni 6 plus. I know
> it had to be an old thread. I just didn't pay any attention to the date.
If
> I have you mixed with someone else problem I appolize.??????????????
> Thanks, mike w4mjr
> Sent from my ALCATEL ONETOUCH A564C
> On Nov 11, 2015 5:14 PM, k8mp@aol.com wrote:
> Hi Mike, Can you refresh my memory
> by pasting the details into an email?
> Thanks, Joe
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Mike < w4mjr@att.net>
> To: k8mp < k8mp@aol.com>
> Sent: Wed, Nov 11, 2015 12:46 PM
> Subject: Ten tec omni 6+
>
>
> Joe I am having the same problem with me 6+ as you
> had with losing the audio. This might be old stuff because I was just
> searching thru the web and saw where you were looking for answer about
your
> rig. Did you get yours repaired and what was the cause.? Thanks, Mike
> w4mjr Sent from my ALCATEL ONETOUCH A564C
>
>
>
>
>
>
>
>
>
>
>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|