Bob: It sure is nice to have an expert to come to with questions. Thanks for
all your work helping
guys out with the right "scoop". That is one of the things that make this
hobby so enjoyable.
Thanks a lot and 73
Clayton N4EV
On Thursday, July 10, 2014 8:37 PM, Bob McGraw - K4TAX <RMcGraw@Blomand.net>
wrote:
There is no front panel IF Filter manual selection available.
Filter selection is either automatic, thus following the DSP BW when I-F
FILTER is set to AUTO.
You can select the filter manually via the MENU on the I-F FILTER line. The
Multi knob makes this choice from the MENU as it steps through all the
filter choices.
73
Bob, K4TAX
----- Original Message -----
From: <bcarling@cfl.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Thursday, July 10, 2014 7:28 PM
Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?
> Thank you. Yes, I read that, and tried it. However, it does not tell me
> how to select them and
> it didn't switch.
>
> What do I rotate or switch?
>
> Is there any way to customize buttons on the front panel to make one of
> them select this filter
> without going through the menu every time?
>
> On 10 Jul 2014 at 19:25, Bob McGraw - K4TAX wrote:
>
>> The I-F FILTER line in the MENU will allow you to switch the filter of
>> your
>> choice manually.
>>
>> 73
>> Bob, K4TAX
>>
>>
>> ----- Original Message -----
>> From: <bcarling@cfl.rr.com>
>> To: <tentec@contesting.com>
>> Sent: Thursday, July 10, 2014 7:17 PM
>> Subject: Re: [TenTec] Invoking OM7 500 Hz filter ?
>>
>>
>> > Thank you Bob. I already did all that. And yes, it is already set to
>> > AUTIO.
>> >
>> > I simply want to know how to switch it on and off when I am operating
>> > the
>> > radio. I thought I
>> > made that clear.
>> >
>> > "Does anyone know how to invoke the 500 Hz Collins filter once it is
>> > installed and enabled?"
>> >
>> >
>> > On 10 Jul 2014 at 19:06, Bob McGraw - K4TAX wrote:
>> >
>> >> Go to the MENU. Scroll to the bottom. Set ENABLE 500 Hz to YES. And
>> >> if
>> >> you
>> >> have the 300 Hz filter do the same for that one. Then at the line I-F
>> >> FILTER select AUTO.
>> >>
>> >> 73
>> >> Bob, K4TAX
>> >>
>> >>
>> >> ----- Original Message -----
>> >> From: <bcarling@cfl.rr.com>
>> >> To: <tentec@contesting.com>
>> >> Sent: Thursday, July 10, 2014 6:42 PM
>> >> Subject: [TenTec] Invoking OM7 500 Hz filter ?
>> >>
>> >>
>> >> > Hello,
>> >> >
>> >> > I now have a clean sounding OMNI VII after doing a master reset.
>> >> > Thanks
>> >> > guys.
>> >> >
>> >> > Does anyone know how to invoke the 500 Hz Collins filter once it is
>> >> > installed and enabled?
>> >> >
>> >> > I have read the manual through twice and still can't figure out how
>> >> > to
>> >> > switch from 2.5 kHz
>> >> > filter to 500 Hz !! Maybe I am not too smart. The book seems to
>> >> > dance
>> >> > all
>> >> > around the topic
>> >> > but never tell you how!
>> >> >
>> >> > 73 - Brian, AF4K
>> >> >
>> >> > Brian Carling, Radio AF4K
>> >> > _______________________________________________
>> >> > TenTec mailing list
>> >> > TenTec@contesting.com
>> >> > http://lists.contesting.com/mailman/listinfo/tentec
>> >> >
>> >>
>> >>
>> >
>> >
>> > Brian Carling, Radio AF4K
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>>
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|