TenTec
[Top] [All Lists]

Re: [TenTec] Orion Power Out

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Orion Power Out
From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 12 Oct 2013 17:03:35 +0200
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I think the first thing to do is to check the watt meter.

Either borrow another watt meter and compare, or try a different
transceiver.
If a second transceiver reads the same or similar, then it's the watt meter.

73
Rick, DJ0IP

-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of art N4UC
Sent: Saturday, October 12, 2013 3:26 PM
To: TenTec reflector
Subject: Re: [TenTec] Orion Power Out

Hi Rick.
RF power measurements are taken both into dummy load and well matched
antenna (SWR=1.2) . Power supply voltage at back panel connector is 13.95V
key-up, and 12.85 key-down on 10, 12.75 on all other bands. More current
being drawn at the higher power outputs. Voltage measurements taken on a
Fluke 8060A meter.

You bring up a good possibility Rick. I am reading the  power output on a
TenTec 1225 wattmeter which I have not calibrated in a long while, so I  do
need to do that.  However, the power meter on the Orion does read 100 (full
scale) on all bands except 10 and 15, where it reads about 75 % of FS on 10
and 85 % on 15.  While these may be pretty close to actual power readings, I
just take these to be values relative to FS.

Tnx es 73, Art

> From: Rick@DJ0IP.de
> To: tentec@contesting.com
> Date: Sat, 12 Oct 2013 10:36:42 +0200
> Subject: Re: [TenTec] Orion Power Out
> 
> Art, are you measuring with a dummy load attached or with an antenna?
> What power supply are you using, and what are its key up and key down 
> voltages at the transceiver back panel?
> 
> 73
> Rick, DJ0IP
> 
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of art 
> N4UC
> Sent: Saturday, October 12, 2013 5:45 AM
> To: TenTec reflector
> Subject: [TenTec] Orion Power Out
> 
> After getting my 565 Orion back from the factory earlier this year, 
> I've noticed that I only get about 50W out on 10M, and 80W on 15. All 
> other bands are over 100W out. I can't say for sure what the numbers 
> were when it went in and I know it's a minor nit in the grand scheme 
> of things, but it's the principle of the thing especially since I 
> don't drive an amp. Is this typical of Orions, or is there a tweak in
order?
> 
> Art/N4UC
>                                         
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
                                          
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>