TenTec
[Top] [All Lists]

Re: [TenTec] Status of New Display Board for OMNI VII

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Status of New Display Board for OMNI VII
From: "Art Roberts W5AER" <w5aer@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 17 Aug 2008 18:07:29 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
An email to Scott (Production Mgr) at sales@tentec.com would be the info  
 from the top.

73
Art
W5AER



On Sun, 17 Aug 2008 18:01:51 -0500, Mike Christiansen  
<starmike@bellsouth.net> wrote:

> Carl, that is a brand new webpage the Tentec just put up last week, so
> the information IMO is current.  This may not be the news your friend
> was hoping for
>
> Mike, N4GW
>
> On Aug 17, 2008, at 6:40 PM, Carl J. Denbow wrote:
>
>> Thanks, Mike. If this is not an old, not-updated post, I was lied to
>> at
>> Dayton.  I was shown a prototype board and was told it was ready for
>> production.  In fact, I was told that the week after Dayton they would
>> be having a production meeting and that the board would be ready for
>> general sales within three months or so.  A friend of mine who
>> bought an
>> ORION II about three years ago was told at that time that the board
>> would be ready "in a few months."  He's ready to ditch his Ten-Ten
>> equipment he is so mad about this issue.  When I gave him the
>> information from Dayton, including my live sitting of the prototype
>> board, he calmed down a little and said he'd give Ten-Tec a few more
>> months.  In short, I hope what I was told at Dayton is more accurate
>> than this link.  Perhaps, at this juncture Ten-Tec's recent "sins" are
>> no more than not updating a web page! :-)
>>
>> Mike Christiansen wrote:
>>> Check this link at the Tentec site.  it should answer your questions
>>>
>>> http://radio.tentec.com/status/
>>>
>>>
>>> On Aug 17, 2008, at 4:19 PM, Carl J. Denbow wrote:
>>>
>>>
>>>> Does anyone know the status the new display board that is coming out
>>>> for
>>>> the OMNI VII and ORION II?  I saw a prototype at Dayton and was
>>>> assured
>>>> that it was ready for production.  This board will allow, among
>>>> other
>>>> things, for real time, continuous spectrum scope (like the ICOM 756
>>>> pro
>>>> series has).  I'm really looking forward to this new board, which is
>>>> supposed to cost in the $300.00 range.
>>>>
>>>> Carl
>>>> N8VZ
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec



-- 
73
Art
W5AER
Houston (we have a problem)
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>