TenTec
[Top] [All Lists]

Re: [TenTec] New Orion Owner needs help

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] New Orion Owner needs help
From: "Neal Campbell" <nealk3nc@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 17 Jun 2006 10:00:32 -0400
List-post: <mailto:tentec@contesting.com>
When I got my Acom 2000A I asked Acom and Tentec about the need for the high
pass filter and they said I would not need it. I certainly have not needed
it yet. I would try it first and see if you have problems before getting
one.

73
Neal K3NC

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Carl Moreschi
Sent: Saturday, June 17, 2006 8:45 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] New Orion Owner needs help

You want keying loop 1 always turned on to use the amp.  You have it wired
correctly.  The amp should key only when you key the radio. Also, there is a
filter required to use the Acom 2000 with the Orion.  This filter is
available from TenTec and is free.

Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message ----- 
From: "John Muzyka" <g4rcg@yahoo.co.uk>
To: "TENTEC" <tentec@contesting.com>
Sent: Saturday, June 17, 2006 5:53 AM
Subject: [TenTec] New Orion Owner needs help


Hi All,
  I got my new 566 Orion 2 yesterday and I am wading my way thru' all the
settings on the rig, which there are lots of, couple of things that I have
found that I am not sure about (cant read and take it in that fast, you know
what its like you want to get it going as soon as poss) is ;-

  1. CW Side tone adjustment where is it??? as it nearly deathens me cant
find reference to Sidetone in the Audio menu's .

  2. ALC light on CW when the rig is keyed it is ON so looks to me as if the
rig is going out of ALC?? cant see any reference to this in the manual

  3. I have connected my Acom 2000a to it with the TX OUT 1 to the KEY IN on
the Acom, and TX EN to KEY OUT on the Acom, this will key the amp but the RX
audio is down, and you can hear the rig being attenuated when you go from
STB (standby) to OPR This in effect like putting a 25Db attenuator in line?
The Keying Loop 1 when set to ON does not key the rig either, turn this off
it keys with the amp but with the attenuated RX

  That is the few things I want to get sorted so I can try and get on the
air this weekend
  Any help would be greatly appreciated
  John G4RCG
  g4rcg@yahoo.co.uk




---------------------------------
 All New Yahoo! Mail - Tired of Vi@gr@! come-ons? Let our SpamGuard protect
you.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>