TenTec
[Top] [All Lists]

[TenTec] Re: Tuners

To: <tentec@contesting.com>
Subject: [TenTec] Re: Tuners
From: RMcGraw@Blomand.Net (Robert & Linda McGraw K4TAX)
Date: Sun, 10 Mar 2002 20:15:40 -0600
That's the way my Omni VI+ and Paragon work.

73
Bob K4TAX

----- Original Message ----- 
From: "WA3FIY" <wa3fiy@radioadv.com>
To: "Carl Moreschi" <n4py@earthlink.net>; "tentec" <tentec@contesting.com>
Sent: Sunday, March 10, 2002 6:52 PM
Subject: Re: [TenTec] Re: Tuners


> I agree with you Carl about this being the best protection I have 
> seen.  As far as I know, it started with the Paragon and I believe 
> it is included in the Pegasus/Jupiter.  Looking at my Jupiter 
> schematic here, I see a current sensing resistor in the power line 
> to the PA stage.  Current information from that resistor is 
> conditioned and sent to the ALC circuit through a potentiometer 
> labelled "Set PA Current Limit".  This leads me to believe that 
> the PJ's are equally like the Paragon, Omni V and Omni VI.
> 
> -Lee-
> 
> 
> On 10 Mar 2002 at 22:14, Carl Moreschi wrote:
> 
> > The Omni VI and Omni V had the best protection I've ever seen
> > for mismatched antennas.  Instead of folding back the transmit power
> > by sensing SWR, they have a collector current sensing circuit that
> > adjusts drive so that the finals can never draw more than 20 amps.
> > These two radios do not require a power supply that shuts off with
> > excessive current.
> > 
> > It is too bad they dropped this circuit in the Pegasus and Jupiter. I
> > bet they will have it in the Orion.
> > 
> > Carl Moreschi N4PY
> > Franklinton, NC
> > ----- Original Message -----
> > From: "George, W5YR" <w5yr@att.net>
> > To: "John Buck" <kh7t@arrl.net>
> > Cc: <tentec@contesting.com>
> > Sent: Sunday, March 10, 2002 8:56 PM
> > Subject: Re: [TenTec] Re: Tuners
> > 
> > 
> > > John, how does this relate to the high-speed circuit breakers built
> > > in to TT power supplies and required if non-TT supplies are used?
> > >
> > > Just curious, since I read your story and then I read other postings
> > > about how a low impedance load drives the collector currents to 30
> > > amps almost instantly and if the fast breaker doesn't operate, poof!
> > > there go the finals . . .
> > >
> > > Straighten me out!   <:}
> > >
> > > 73/72/oo, George W5YR - the Yellow Rose of Texas
> > > Fairview, TX 30 mi NE of Dallas in Collin county EM13qe
> > > Amateur Radio W5YR, in the 56th year and it just keeps getting
> > > better! QRP-L 1373 NETXQRP 6 SOC 262 COG 8 FPQRP 404 TEN-X 11771
> > > I-LINK 11735 Icom IC-756PRO #02121  Kachina 505 DSP  #91900556  Icom
> > > IC-765 #02437
> > >
> > > All outgoing email virus-checked by Norton Anti-Virus 2002
> > >
> > >
> > > John Buck wrote:
> > > >
> > > > The TenTec design approach of designing a Crunch proof 100 watt
> > > > amplifier with at least a 3 to 1 full power capability will make
> > > > it easy to use many antennas over the whole band without tuner and
> > > > without blowing up the radio.
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > 
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> > 
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 



<Prev in Thread] Current Thread [Next in Thread>