I am getting ready to make a QSK interface cable for the FT-1000 MP MK V to
an Alpha 78 and see if the QSK will work. It is working on the test bench
with ohmmeter.
Reading the Mk V manual One part says 40V max and in another sentence it
says 15V max. Is it safe to use a direct hookup with the Alpha 78 QSK
voltages.
My current amp interface cable uses an external pc relay keyed by pin 2 to
key 'older' amps with open frame relays.
Paul K3PG
If using another manufacturer’s QSK linear, and if
its switching circuitry consumes less than 150 mA of
DC voltage below 40 V, you can connect the Tx/Rx
switching line for the linear to pin 2 (“TX GND”) of the
BAND DATA jack (use pin 3 for ground), and the linear’s
exciter-enable output to pin 8 (“TX INHIBIT”) of the
BAND DATA jack. This line must be switched to ground
to enable transmission once the linear is ready for excitation
from the MARK-V FT-1000MP. If your QSK linear
sinks more than 100 mA or uses more than 15 V
for T/R relay switching, you will have to provide a suitable
external interface transistor, controlled by pin 2.
Be certain to make provision for suitable reduction of
the drive power from the MARK-V FT-1000MP, so as
not to damage your amplifi
On Tue, Feb 16, 2010 at 3:00 PM, <yaesu-request@contesting.com> wrote:
> Send Yaesu mailing list submissions to
> yaesu@contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/yaesu
> or, via email, send a message with subject or body 'help' to
> yaesu-request@contesting.com
>
> You can reach the person managing the list at
> yaesu-owner@contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Yaesu digest..."
>
>
> Today's Topics:
>
> 1. FT450 Linear Jack (Bry Carling)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Tue, 16 Feb 2010 08:09:42 -0500
> From: "Bry Carling" <bcarling@cfl.rr.com>
> Subject: [Yaesu] FT450 Linear Jack
> To: yaesu@contesting.com
> Message-ID: <4B7A52C6.23626.240CEDE@bcarling.cfl.rr.com>
> Content-Type: text/plain; charset=ISO-8859-1
>
> Does anyone know if Yaesu provides a PLUG with their FT450 radios
> for the LINEAR JACK?
>
> It appears to be some kind of 10-pin DIN connector...
>
> Anyone have experience using this jack to switch T-R control to a relay fo
> an
> external (non-Yaesu) linear amplifier???
>
> Thanks & 73 - Brian, AF4K
>
> -~???????~-"?r? in FL?R???"-~???????~-
>
>
>
>
>
> ------------------------------
>
> _______________________________________________
> Yaesu mailing list
> Yaesu@contesting.com
> http://lists.contesting.com/mailman/listinfo/yaesu
>
>
> End of Yaesu Digest, Vol 86, Issue 7
> ************************************
>
--
Paul Gerhardt
K3PG
http://pgerhardt.blogspot.com
QRP ARCI 6674
FP 274
_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu
|