Yaesu
[Top] [All Lists]

[Yaesu] RE: [AMPS] End to background noise

To: <yaesu@contesting.com>
Subject: [Yaesu] RE: [AMPS] End to background noise
From: Joseph.F.Nemecek@twa.com (Nemecek, Joseph F.)
Date: Mon, 20 Oct 1997 13:12:49 -0500
If you want the data sheets Morel mentions FAXed to you. Dial
800-446-6212 and enter FAX Code number: 1956.
Joe, K0JN

>----------
>From:  Morel Grunberg[SMTP:morel.grunberg@telrad.co.il]
>Sent:  Monday, October 20, 1997 2:01 AM
>To:    'Amplifier reflector'
>Cc:    'Cq-contest'; 'FT-1000MP list'; 'Ham-equip'; 'Towertalk'; 'Yaesu
>reflector'
>Subject:       [AMPS] End to background noise
>
>Few months ago I heard that "Analog Devices" has a new 
>integrated circuit ( SSM-2166 ) who is able to cancel the
>background noise present in an audio signal coming from
>a microphone. 
>
>After I received the 15-pages data specs & application note
>I discovered that this tiny 14-pin IC can solve my background
>problems coming from the amplifier blower, computer fan, TV
>and radio sound, children cries and a busy street down under 
>my window shack.
>
>After I've built the circuit and  began the tests, I was astonished
>by the effectiveness of the IC: simply all the background noise
>was attenuated with an average of 35dB down of my voice. The 
>air reports were excellent and all my partners asked me what
>I'm using to cancel the noises, after a short demonstration with
>the unit bypass switch on/off. Now, I can use my processor at
>compression levels much bigger than the previous 3-4 dB I used
>before due to the high background noise with extremely low 
>distortions ( typical 0.1-0.2% ). Absolute no voice alterations or
>any kind of time delays, echo or signal rise/fall timing related
>problems
>(as in other products) were found.   
>
>The unit is quite simple: an IC, 5-6 capacitors, 3-4 resistors and
>5 small variable resistors. The supply is 5Vdc@15mA or 12-25V
>if a simple 7805 regulator is used. The board can be as small as
>3x4cm and should be placed in a small shielded box.
>
>Some modifications should be made on the original schematic diagram
>and setting procedure given in the "Analog Devices" application note.
>
>The unit was tested with Yaesu/Kenwood/Icom transceivers and 
>performed very well with no RF feedbacks. The only difference is
>of course, the microphone connector wiring.
>
>Few of my local friends built also this small unit with very good
>results 
>too. As I've heard, a complete kit and and an assembled kit will be
>available very soon in U.S. Also, an article on this issue will appear
>in "QST" very soon, as I've heard from some U.S. friends. 
>
>The unit is very useful for SSB contest teams when few operators
>are crying in their microphones at same time creating a stressing
>noisy environment.
> 
>The "Analog Devices" complete documentation can be found on their
>home page ( www.analog.com ) and can be read with Acrobat Reader
>software. If you don't have this program on your computer, you can
>download for free immediately via a link to "Adobat".
> 
>The 15-pages can be received also from Customer Support Hot Line
>automatic fax : 1-800-262-5643.
> 
>73 de Morel, 4X1AD
> 
>
>--
>FAQ on WWW:               http://www.contesting.com/ampfaq.html
>Submissions:              amps@contesting.com
>Administrative requests:  amps-REQUEST@contesting.com
>Problems:                 owner-amps@contesting.com
>Search:                   http://www.contesting.com/km9p/search.htm
>

--
FAQ on WWW:               http://www.qsl.net/k7on/yaesu.html
Submissions:              yaesu@contesting.com
Administrative requests:  yaesu-REQUEST@contesting.com
Problems:                 owner-yaesu@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm

<Prev in Thread] Current Thread [Next in Thread>
  • [Yaesu] RE: [AMPS] End to background noise, Nemecek, Joseph F. <=