WriteLog
[Top] [All Lists]

Re: [WriteLog] Writelog prints extra characters.

To: "'Writelog Reflector'" <writelog@contesting.com>
Subject: Re: [WriteLog] Writelog prints extra characters.
From: "Don Hill AA5AU" <aa5au@bellsouth.net>
Date: Fri, 23 Feb 2018 06:07:27 -0600
List-post: <mailto:writelog@contesting.com>
After a closer look at this, it appears the issue is with 2Tone printing later 
than MMTTY. If you have your MONITOR turned on and listening to your transmit 
RTTY tones, 2Tone in a receive only is also decoding your transmit. When you 
stop transmitting, 2Tone will continue to print what you sent but in a delayed 
manner which is inherent to 2Tone. There's nothing that can be done about it 
except to turn MONITOR off and not listen to your TX tones.

Don AA5AU

-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Don AA5AU
Sent: Wednesday, February 21, 2018 2:12 PM
To: Writelog Reflector
Subject: Re: [WriteLog] Writelog prints extra characters.

Mike, I think I know what you are talking about and I think I've seen this as 
well. I don't think it has any bearing on what actually is sent. I thought it 
was limited to 2Tone but I have not really taken time to look at it. The reason 
I think I'm seeing it is because many times I see my call in print and I think 
it's from the other station (I do mostly S&P), but then I realize that it's the 
extra characters showing after I transmit. Most times I see my entire callsign 
print and not just partial as you are seeing.
I don't worry about it. It's been going on for some time. Not sure when it 
started but for me, it doesn't appear to be an issue.
Don AA5AU

      From: Mike Streeter via WriteLog <writelog@contesting.com>
 To: Writelog Reflector <writelog@contesting.com> 
 Sent: Wednesday, February 21, 2018 2:05 PM
 Subject: [WriteLog] Writelog prints extra characters.
   
I have been using Writelog for RTTY for years. Recently a strange new  problem 
has started. After I send a message from  any of the F keys the Rttyrite panel 
will print the last two or three characters again. It shuts of the radio PTT 
when it should so does not send them, just prints them. For example if I hit an 
F key that is programmed to send my call sign it will send wm5dx (in blue)  
just as it should but will follow by showing 5DX (in black) as though it is 
incoming text. It happens every time using either MMTTY or 2 Tone but it does 
not happen if I send using MMTTY stand alone rather than Writelog.I have 2 
Navigator interfaces and it happens with both of them. I have uninstalled and 
reloaded the Writelog software and it continues to happen. It happens to any 
message from any F key. If I send 5NN TU it will send just that but also print 
TU.It makes it look like after I have sent my call I am receiving the end of my 
call from a station responding to my call.Radio is a K3 
 and OS is Windows 10.
Anyone have any ideas?
Thanks for reading this far,
Mike, WM5DX.
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/


   
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>