please take me off the list
On Thursday, February 12, 2015 3:32 PM, "writelog-request@contesting.com"
<writelog-request@contesting.com> wrote:
Send WriteLog mailing list submissions to
writelog@contesting.com
To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/writelog
or, via email, send a message with subject or body 'help' to
writelog-request@contesting.com
You can reach the person managing the list at
writelog-owner@contesting.com
When replying, please edit your Subject line so it is more specific
than "Re: Contents of WriteLog digest..."
Today's Topics:
1. CW Decode (Rod via WriteLog)
2. Re: CW Decode (Gary AL9A)
3. Re: CW Decode (joeduerbusch)
4. Re: Antenna to __ Azimuth? (Anthony Buscaglia)
5. Rotor Control (joeduerbusch)
6. Re: Rotor Control (Gary AL9A)
----------------------------------------------------------------------
Message: 1
Date: Wed, 11 Feb 2015 13:33:02 -0500
From: Rod via WriteLog <writelog@contesting.com>
To: writelog@contesting.com
Subject: [WriteLog] CW Decode
Message-ID: <8301.6fcc86bb.420cfa5e@aol.com>
Content-Type: text/plain; charset="US-ASCII"
The cw decoder quit working. Using it as a audio panadapter helps to zero
beat. What WL file has this function? Any suggestions?
73
Rod W7OM
PS: Windows 7, MicroHAM Keyer II to FT-1000MP WL 11.24J
------------------------------
Message: 2
Date: Wed, 11 Feb 2015 11:07:44 -0900
From: "Gary AL9A" <al9a@mtaonline.net>
To: <writelog@contesting.com>
Subject: Re: [WriteLog] CW Decode
Message-ID: <64C3C29ACD79469EB91A2F1C48E32D61@AL9APC>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
Hi Rod,
I'm a bit confused by your statement that "The cw decoder quit working".
What decoder? WL does CW decoding via the Rttyrite window. Is it the
Rttyrite window that is not decoding?
A component part of Rttyrite is a smaller window called "WriteLog CW
Receiver" that has two vertical bars and shows 750 Hz of bandwidth. The
short vertical bar is fixed at the center of the window, while the longer
vertical bar shows your CW tone. When receiving CW the waveform displays in
this window and moving the VFO will allow you to zero beat the signal.
There are also settings for min and max speed settings to decode. Is this
the window you are talking about? Is the window visible, but no wave form
displays? What are the min and max settings? This window is a function of
the settings in your Rttyrite window so it would be helpful to know what
those are?
Or, are you talking about the Window/CW Display window which is a
multi-channel decoder? This windows decodes multiple channels, I think up
to six channels. It also has a small vertical window with a small
horizontal bar in the window center. I never use this one, but I think this
small window also shows incoming wave form. I doubt this is the window you
are trying to use, but am not certain.
73,
Gary AL9A
-----Original Message-----
From: Rod via WriteLog
Sent: February 11, 2015 9:33 AM
To: writelog@contesting.com
Subject: [WriteLog] CW Decode
The cw decoder quit working. Using it as a audio panadapter helps to zero
beat. What WL file has this function? Any suggestions?
73
Rod W7OM
PS: Windows 7, MicroHAM Keyer II to FT-1000MP WL 11.24J
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
------------------------------
Message: 3
Date: Wed, 11 Feb 2015 20:10:33 +0000
From: joeduerbusch <k0bx@arrl.net>
To: Gary AL9A <al9a@mtaonline.net>
Cc: "writelog@contesting.com" <writelog@contesting.com>
Subject: Re: [WriteLog] CW Decode
Message-ID:
<CALfacscMAVvBCTs08zOjPTzF_46DF3F3J4Fr15Xjt=ScNMKEYQ@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8
When it stops working means there is NO audio getting to it. Check your
MicroHamKeyer if it has a soundcard built in. Otherwise check to see if
you can play a CD of music in Windows.
Joe K0BX
On Wed, Feb 11, 2015 at 8:07 PM, Gary AL9A <al9a@mtaonline.net> wrote:
> Hi Rod,
>
> I'm a bit confused by your statement that "The cw decoder quit working".
> What decoder? WL does CW decoding via the Rttyrite window. Is it the
> Rttyrite window that is not decoding?
>
> A component part of Rttyrite is a smaller window called "WriteLog CW
> Receiver" that has two vertical bars and shows 750 Hz of bandwidth. The
> short vertical bar is fixed at the center of the window, while the longer
> vertical bar shows your CW tone. When receiving CW the waveform displays
> in this window and moving the VFO will allow you to zero beat the signal.
> There are also settings for min and max speed settings to decode. Is this
> the window you are talking about? Is the window visible, but no wave form
> displays? What are the min and max settings? This window is a function of
> the settings in your Rttyrite window so it would be helpful to know what
> those are?
>
> Or, are you talking about the Window/CW Display window which is a
> multi-channel decoder? This windows decodes multiple channels, I think up
> to six channels. It also has a small vertical window with a small
> horizontal bar in the window center. I never use this one, but I think
> this small window also shows incoming wave form. I doubt this is the
> window you are trying to use, but am not certain.
>
> 73,
> Gary AL9A
>
>
>
> -----Original Message----- From: Rod via WriteLog
> Sent: February 11, 2015 9:33 AM
> To: writelog@contesting.com
> Subject: [WriteLog] CW Decode
>
>
> The cw decoder quit working. Using it as a audio panadapter helps to zero
> beat. What WL file has this function? Any suggestions?
>
> 73
>
> Rod W7OM
>
> PS: Windows 7, MicroHAM Keyer II to FT-1000MP WL 11.24J
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
--
#1 Honor Roll Mixed
Honor Roll RTTY
5BWAS
Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk)
without my permission.
------------------------------
Message: 4
Date: Wed, 11 Feb 2015 16:12:15 -0500
From: Anthony Buscaglia <tonybb@me.com>
To: Writelog Reflector <writelog@contesting.com>
Subject: Re: [WriteLog] Antenna to __ Azimuth?
Message-ID: <7215C763-4519-42C9-A4AA-215701E5DF7F@me.com>
Content-Type: text/plain; charset=us-ascii
Gary,
I knew it was there I just couldn't find it!
Thanks for the info on entering the azimuth.
Very nice!
73
Tony
K2NV
On Feb 10, 2015, at 11:41 PM, Gary AL9A <al9a@mtaonline.net> wrote:
> Tony,
>
> I never used the Alt+A command as it requires two keys to do it. I created a
> keyboard shortcut by programing the Grave key, that's the one just to the
> left of the number 1 key - `, so that I can turn the antenna with a single
> key press based upon the call in the Entry window. The shortcut command is
> "RadioAntennaToAzimuth".
>
> Also the latest WL version, 11.24J, contains a new feature for antenna
> azimuth. If the call field is empty just type in a number less than 360 and
> hit Enter. WL will begin turning the antenna to that direction without
> needing a call in the CALL field. Great feature when doing S&P and only get
> a partial or marginal copy on the call, but enough to recognize the general
> direction of where the beam should be pointed.
>
> 73,
> Gary AL9A
>
> -----Original Message----- From: Anthony Buscaglia
> Sent: February 10, 2015 7:00 AM
> To: Writelog Reflector
> Subject: [WriteLog] Antenna to __ Azimuth?
>
> What happened to the ALT-A to turn the Antenna?
> I tried to add it back in the Keyboard Shortcuts, but did not find a command
> for it.
>
> I'm sure it's simple, but I can't remember how to get it back....
>
> Anyone?
>
> Tnx
> 73
> Tony
> K2NV
>
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
------------------------------
Message: 5
Date: Thu, 12 Feb 2015 01:26:43 +0000
From: joeduerbusch <k0bx@arrl.net>
To: "writelog@contesting.com" <writelog@contesting.com>
Subject: [WriteLog] Rotor Control
Message-ID:
<CALfacsdKfUSDUEMFyL_M3qewRO11TVPNNOMhrhqqooHXR0TDUg@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8
I have been using Rotor Control for a long time and it works just fine.
But :
Also the latest WL version, 11.24J, contains a new feature for antenna
azimuth. If the call field is empty just type in a number less than 360 and
hit Enter. WL will begin turning the antenna to that direction without
needing a call in the CALL field. Great feature when doing S&P and only get
a partial or marginal copy on the call, but enough to recognize the general
direction of where the beam should be pointed.
73,
Gary AL9A
I have tried this after updating to version 11.24j and restarting WL but no
luck getting it to work.
Is there something else I need to do??
Joe K0BX
--
#1 Honor Roll Mixed
Honor Roll RTTY
5BWAS
Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk)
without my permission.
------------------------------
Message: 6
Date: Wed, 11 Feb 2015 20:03:15 -0900
From: "Gary AL9A" <al9a@mtaonline.net>
To: "joeduerbusch" <k0bx@arrl.net>, <writelog@contesting.com>
Subject: Re: [WriteLog] Rotor Control
Message-ID: <A8956363860B4F7D8F48F3EE05DAC82F@AL9APC>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
Joe,
My bad, the new functionality of "Radio/Antenna to this azimuth" for numbers
0 through 359 in the CALL field was added in V11.22, not 11.24. I didn't
have to do anything to activate this function. The Help manual includes the
following:
"Turn Antenna to the azimuth indicated by the call sign in the current Entry
Window. If the "call sign" is digits indicating a number from 0 through 359,
then that number is taken to be the desired rotator azimuth. This menu entry
is disabled (gray) if WriteLog does not detect antenna control software
installed."
Check the WL menu selections at the top of the screen. Under the Radio menu
item there should be an entry "Antenna to this Azimuth". Per the help item
above, if this selection is grayed out WL is not detecting your antenna
control software. It recognized my Green Heron RT-21, which at that time
was configured to drive a Create Design rotor. That rotor has since died
and I will not be able to replace it with the new Alpha-Spid I have sitting
under the desk until later this spring. I have reconfigured the RT-21 to
work with the Alpha-Spid and did a bench test, but forgot to check if the WL
azimuth function would work as before. But, since it worked previously, I'm
sure it will work again once the rotor is installed.
73,
Gary AL9A
-----Original Message-----
From: joeduerbusch
Sent: February 11, 2015 4:26 PM
To: writelog@contesting.com
Subject: [WriteLog] Rotor Control
I have been using Rotor Control for a long time and it works just fine.
But :
Also the latest WL version, 11.24J, contains a new feature for antenna
azimuth. If the call field is empty just type in a number less than 360 and
hit Enter. WL will begin turning the antenna to that direction without
needing a call in the CALL field. Great feature when doing S&P and only get
a partial or marginal copy on the call, but enough to recognize the general
direction of where the beam should be pointed.
73,
Gary AL9A
I have tried this after updating to version 11.24j and restarting WL but no
luck getting it to work.
Is there something else I need to do??
Joe K0BX
--
#1 Honor Roll Mixed
Honor Roll RTTY
5BWAS
Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk)
without my permission.
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
------------------------------
Subject: Digest Footer
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
------------------------------
End of WriteLog Digest, Vol 146, Issue 8
****************************************
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|