Hi Gary for your comments. The Antenna to this Azimuth works fine, I also
setup a short-cut key with the "Grave" key to turn the rotor. I am using a
RotorE-Z board inside the HamIV control box.
On my website I even wrote a VB program to turn the rotor.
When I type in a beamheading, such as 109, hit enter, I just get a beep
from windows. So thanks again I will continue trying.
Joe K0BX
On Thu, Feb 12, 2015 at 5:03 AM, Gary AL9A <al9a@mtaonline.net> wrote:
> Joe,
>
> My bad, the new functionality of "Radio/Antenna to this azimuth" for
> numbers 0 through 359 in the CALL field was added in V11.22, not 11.24. I
> didn't have to do anything to activate this function. The Help manual
> includes the following:
>
> "Turn Antenna to the azimuth indicated by the call sign in the current
> Entry Window. If the "call sign" is digits indicating a number from 0
> through 359, then that number is taken to be the desired rotator azimuth.
> This menu entry is disabled (gray) if WriteLog does not detect antenna
> control software installed."
>
> Check the WL menu selections at the top of the screen. Under the Radio
> menu item there should be an entry "Antenna to this Azimuth". Per the help
> item above, if this selection is grayed out WL is not detecting your
> antenna control software. It recognized my Green Heron RT-21, which at
> that time was configured to drive a Create Design rotor. That rotor has
> since died and I will not be able to replace it with the new Alpha-Spid I
> have sitting under the desk until later this spring. I have reconfigured
> the RT-21 to work with the Alpha-Spid and did a bench test, but forgot to
> check if the WL azimuth function would work as before. But, since it
> worked previously, I'm sure it will work again once the rotor is installed.
>
> 73,
> Gary AL9A
>
> -----Original Message----- From: joeduerbusch
> Sent: February 11, 2015 4:26 PM
> To: writelog@contesting.com
> Subject: [WriteLog] Rotor Control
>
>
> I have been using Rotor Control for a long time and it works just fine.
> But :
>
> Also the latest WL version, 11.24J, contains a new feature for antenna
> azimuth. If the call field is empty just type in a number less than 360
> and
> hit Enter. WL will begin turning the antenna to that direction without
> needing a call in the CALL field. Great feature when doing S&P and only
> get
> a partial or marginal copy on the call, but enough to recognize the general
> direction of where the beam should be pointed.
>
> 73,
> Gary AL9A
>
> I have tried this after updating to version 11.24j and restarting WL but no
> luck getting it to work.
> Is there something else I need to do??
>
>
> Joe K0BX
>
>
> --
>
> #1 Honor Roll Mixed
> Honor Roll RTTY
> 5BWAS
>
> Stop the insanity!
> Please do not add me to any distribution lists (Joke, Stories or Junk)
> without my permission.
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
--
#1 Honor Roll Mixed
Honor Roll RTTY
5BWAS
Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk)
without my permission.
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|