>> Some may think Rigblaster is the problem, if so why would it
>> work fine with MMTY alone ? I have operated RTTY for a number
>> of years and feel funny I cant figure this out.
Which version of Rigblaster do you have?
Are you also using the RigBlaster for CW and (all mode) PTT?
What port are you using for transceiver control (CAT) and what
port are you using for FSK?
Are you using "real" RS-232 ports or USB to RS-232 converters?
Is MMTTY configured to use a COM port for the PTT & FSK port
(TX Tab) or are you using EXTFSK?
Is MMTTY configured for radio control when it is run in stand
alone mode?
Are you using the same installation of MMTTY when you run in
stand alone mode as when you use it with WriteLog?
73,
... Joe, W4TV
On 1/16/2011 7:35 PM, rob beaudoin wrote:
> Hi All
>
> Well in my continuing quest to resolve my Writelog/mmyt/rigblaster
> combo I have discovered more infomation.
>
> First let me say thank you thank you too:
> Jim AD1C John W5IFP Walt w6sa Jim n7us Don AA5AU
> Irwin KD3TB Steve n4dxs Ed W0YK Dick W0RAA
>
> As you can see many offered sugestions.. W5IFP was thinking along the
> lines I was about comport 4 already being used for something.
>
> Unfortunately I have not solved issue. Let me give some info again and
> something I just recently noticed.......Believe me I have probably
> 12 hours or so over a few days invested in this.
>
> MMTY by itself work FB.......Writelog great in cw/ssb. RTTY with
> writelog NO. I have used writelog with mmty for many years and really
> like it. Recently I got a good used 3 year old computer and tried to get
> Write/MMTY going ....No luck All new version of Writelog
> being use. I have a ft1000mp and Rigblaster Plus.
> using FSK. This has worked well for me till now.
>
> Info If you start MMTY by itself my digital light on rigblaster is off
> TILL you press
> TX. Upon returning to recieve digital light goes out.....Fine
> Eveen after a reboot If I I load writelog with any contest module
> Rigblaster light comes on.
> It stays on.......I have not even told it to bring RTTY screen yet.
> No amount of changes to MMTY inside of writelog do anything.
> RTTY screen will load MMTY and it is fine for RX It does not matter
> what port I tell rtty screen I use it always say port not available. If I
> press
> TX on MMTY screen I get carrier no didle. Pressing RX does turn it off.
> So something is happening.
> In main writelog screen I have port 1 set for frequency control of readout.
> This works ok.
> I took the time to setup spare computer with older versions of writelog
> and mmty. Exact same results.???? I am thinking Writelog
> has taken control of the comports and will not let MMTY do its
> thing. Some may think Rigblaster is the problem, if so why would it
> work fine with MMTY alone ? I have operated RTTY for a number of
> years and feel funny I cant figure this out. I had a simmilar problem
> 1 1/2 years ago.......At that time I believe it was Dick W0RAA who
> got me going in right diredtion. Believe me if I ever get this going
> again I will write down EVERYTHING !!
> Thanks in advance to any that may have sugestion......Your time really is
> appreciated.
> 73 BoB WA1FCN
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|