WriteLog
[Top] [All Lists]

Re: [WriteLog] Problem with WriteLog and WinKey?

To: "'Jim Reisert AD1C'" <jjreisert@alum.mit.edu>, "'K0HB'" <K0HB@arrl.org>
Subject: Re: [WriteLog] Problem with WriteLog and WinKey?
From: "Joe Subich, W4TV" <lists@subich.com>
Reply-to: lists@subich.com
Date: Sat, 5 Sep 2009 14:29:04 -0400
List-post: <writelog@contesting.com">mailto:writelog@contesting.com>

> On Sat, Sep 5, 2009 at 11:20 AM, K0HB<kzerohb@gmail.com> wrote:
> 
> > Writelog-via-urouter over-rides the front panel pot.  (As far as I
> > know, it always did.)

No, Router is not overriding WriteLog.  WriteLog implements the 
"pot lock" mode in WinKey and current versions of Router respect  
the application's settings.  

In "pot lock" mode, WinKey (and Router) reports changes in the 
speed pot setting to the application.  It is the responsibility of 
the application to explicitly set the WinKey CW speed.  WriteLog 
sets the speed in the discrete preprogrammed steps.  The current 
implementation of Router is no different than Writelog with a 
K1EL WinKeyer 2 or WinKey USB alone. 

> Write Log (at the bottom) now says 24 WPM, but the actual speed
> coming out of the keyer jumps by several WPM.  There's a disconnect 
> somewhere between the speed that Write Log reports, and the one 
> it's actually sending at. 

CW speed is responsibility of the application.  Enable the WinKey 
monitor in Router to see what the WriteLog is sending to the 
WinKey. 

73, 

   ... Joe, W4TV 
 



> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com] On Behalf Of Jim Reisert AD1C
> Sent: Saturday, September 05, 2009 1:25 PM
> To: K0HB
> Cc: Writelog
> Subject: Re: [WriteLog] Problem with WriteLog and WinKey?
> 
> 
> On Sat, Sep 5, 2009 at 11:20 AM, K0HB<kzerohb@gmail.com> wrote:
> 
> > Writelog-via-urouter over-rides the front panel pot.  (As far as I
> > know, it always did.)
> 
> Hans, I don't think it's as straightforward as that.  Say I'm
> sending CQ at 23 WPM.  While the CQ is sending, I turn the 
> microKEYER speed dial slightly,  WriteLog (at the bottom) now 
> says 24 WPM, but the actual speed coming out of the keyer 
> jumps by several WPM.  There's a disconnect somewhere between 
> the speed that WriteLog reports, and the one it's actually sending at.
> 
> 73 - Jim AD1C
> 
> --
> Jim Reisert AD1C, <jjreisert@alum.mit.edu>, 
> http://www.ad1c.us _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com 
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>