WriteLog
[Top] [All Lists]

Re: [WriteLog] WL & IC-706 setup for Field Day

To: "'Gary AL9A'" <al9a@mtaonline.net>, "'Writelog Reflector'" <writelog@contesting.com>
Subject: Re: [WriteLog] WL & IC-706 setup for Field Day
From: "Joe Subich, W4TV" <lists@subich.com>
Reply-to: lists@subich.com
Date: Sun, 21 Jun 2009 00:50:19 -0400
List-post: <writelog@contesting.com">mailto:writelog@contesting.com>
Gary, 

To get this information into the archives (again), another way 
to support unsupported Icom transceivers is to use the override 
function in the [RIGS] part of writelog.ini.  

 > The following entries override WriteLog's default setting 
 > for the Icom rig address for the various Icom rigs.  All 
 > rigs that have Icom rig addresses have corresponding entries 
 > in WriteLog.ini here under the name that matches the name 
 > in the Setup Ports dialog including space characters!
 > 
 > Icom IC-781=0x33
 > Icom IC-756PRO=0x12

For example, since the IC-706mkIIg is not supported directly 
one could add the following entry: 

Icom IC-706=0x58 

and then select IC-706 as the transceiver in Writelog.  This 
avoids the need to change the IC-706mkIIg default address. 

Similarly, the IC-756Pro3 can be overridden for use with the 
IC-7600 until specific support for the 7600 is added. 

73, 

   ... Joe, W4TV 
 



> -----Original Message-----
> From: writelog-bounces@contesting.com 
> [mailto:writelog-bounces@contesting.com] On Behalf Of Gary AL9A
> Sent: Saturday, June 20, 2009 8:35 PM
> To: Writelog Reflector
> Subject: Re: [WriteLog] WL & IC-706 setup for Field Day
> 
> 
> WELL CALL ME STUPID!!  I found the answer in the WL archives 
> immediately 
> AFTER sending the missive below.  The IC-706 hex code is 48H and all 
> versions of the 706 must be set to this code to work in WL.  
> I would like to 
> thank the author of the solution for his time consuming and 
> painstaking work 
> in finding the solution.  That author would be ME, back in 
> Oct. 2004!!! 
> Getting old sure ain't pretty!
> 
> 73,
> Gary AL9A
> 
> 
> 
> ----- Original Message ----- 
> From: "Gary AL9A" <al9a@mtaonline.net>
> To: "Writelog Reflector" <writelog@contesting.com>
> Sent: June 20, 2009 4:25 PM
> Subject: [WriteLog] WL & IC-706 setup for Field Day
> 
> 
> > Spent the better part of a frustrating afternoon setting up a Field 
> > Day station in my RV.  Rig is an IC-706MKII and I'm using a new net 
> > book computer, the ASUS 1000HA.  WL installed ok and I think I have 
> > everything configured correctly, but Murphy spent the afternoon 
> > looking over my shoulder.
> >
> > The interface is a USB to 2 port serial adaptor, which 
> WinXP has setup 
> > as Comm3 and Comm4.  Comm3 goes to a Rigblaster Plus, Comm4 to the 
> > radio via a CT-17 Level Converter.  I'm planning on running a CW 
> > station and have receive working ok through the Rittyrite 
> CW decoder.  
> > Problem is I can't get
> > the radio and laptop to communicate.  The band map has no 
> idea what band 
> > or
> > mode is set on the the radio.  I've checked and rechecked 
> all the wiring
> > hookups and can find nothing amiss.  I've used the 
> IC-706MKII radio before
> > with WL on my main desk station with a different computer 
> when my main 
> > radio
> > was in the repair shop a couple of years ago, with 
> virtually the same
> > interface setup, so I know it works.
> >
> > I'm sure it's a configuration issue somewhere.  Just as I 
> was throwing 
> > in the towel for the day I thought I heard Murphy whispering in my 
> > ear.  I haven't used the 706 for sometime and when I reviewed the 
> > operator manual I discovered that the hex address in the radio was 
> > different than what the book default value is.  Without thinking I 
> > reset the radio to the default. Now, I'm thinking that was 
> the bullet 
> > I put squarely into my foot!  The list
> > of radios in the WL Ports section shows IC-706, not IC-706MKII or
> > IC-706MKIIG.  So now me thinks that a couple of years ago I 
> changed the 
> > hex
> > address to what the original IC-706 hex code is as that is 
> probably what 
> > the
> > WL rig interface is programmed with.  Problem is I don't 
> remember what the
> > hex setting was!  Anyone know what the hex address code is for the 
> > original
> > IC-706?  I suspect that if I change that setting in the 
> radio the problem
> > will be resolved.  HELP!!!
> >
> > 73,
> > Gary AL9A
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com 
> > http://lists.contesting.com/mailman/listinfo/writelog
> > WriteLog on the web:  http://www.writelog.com/
> 
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com 
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/

_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>