FSK is advisable for many reasons. The most straightforward approach is to
use a legacy serial port to send FSK and PTT signals to the RTTY connector
on the back of the FT-990, 1000MP, or MARK-V MP. Use the TxD pin for the
FSK shift signal and the RTS pin for the PTT signal. You can make a simple
transistor switch cable using a 1K resistor and a 2N2222 or 2N3904
transistor. I think AA5AU has diagrams on his website at www.aa5au.com
somewhere. An older rendition, originally on N1RCT's website, is at
http://www.w5bbr.com/pttfsk.html.
Pinouts for the 1000MP RTTY and PACKET connectors are at
http://www.qsl.net/wa9als/pk232.htm.
A couple of little-known facts:
1. The PTT pins of the MP's RTTY and PACKET connectors are in parallel.
Without going into detail, depending on how many cables and modes you
make/operate, this knowledge can save you a wire/cable.
2. With the 1000MP series and the IC-756PRO series, you don't need the
transistor in the cable for the FSK line - You can just feed TxD through a
1K resistor directly to the FSK pin of the RTTY connector. I first saw this
mentioned in K6STI's documentation for his RITTY program. Wired like this
for several years now - no problems.
3. I had a third point, but I forgot it! ;-))
Of course, you will soon want to operate 2 instances of MMTTY, and you can
get some ideas about that at http://www.qsl.net/wa9als/so2r-mmttyx2.htm
I've wired the 990, 1000MP, MARK-V, IC-756PRO, and PROII using transistor
interfaces. You will have a very difficult time, or find it impossible, to
key the MP using a simple optoisolator.
Any questions, this list will be glad to help! 73 - John, WA9ALS
www.wa9als.com
----- Original Message -----
From: "Hank Lonberg" <kr7x@comcast.net>
To: <writelog@contesting.com>
Sent: Sunday, December 28, 2003 11:33 PM
Subject: [WriteLog] RTTY/MMTTY/Yaesu ft 1000 mp Mk V help
> I am going to try to give RTTY a go with WLog/MMTTY and my Mark
> V. I am thinking of using FSK with the XCVR but am a little confused
about
> the connections and interfacing to make it all work.
>
> I have searched the archives of both WLog and RTTY reflectors. Still not
to
> sure if I use the serial port to send PTT then where do I get the FSK
signal
> to connect up to the FSK input on the rig? Or should I just have the
serial
> rig control key the PTT and use the soundcard for rtty signal.
>
> I am looking to have rig control, writlog logging and rtty all at the same
> time. I'm sure this has been done with the FT 1000MP before so as to not
bog
> down the list please respond direct.
>
> A nice hook up schematic would be helpful.
>
> 73
>
> Hank/KR7X
> IH9P Pantelleria Contest Team
> Tikirriki Contest Club
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|