Thanks for the recent dialog, John - I think it has helped us both! I
had DX Telnet going with Writelog, but hadn't tried it yet with DX4WIN.
I started trying last night, but didn't get it. After your post below,
I tried again, and got it going with DX4WIN. However, I still didn't
know how to get DX Telnet going exporting spots to BOTH DX4WIN and
Writelog AT THE SAME TIME, which it's advertised to do.
I finally figured it out using the DX Telnet DUPER program. This is
exactly what DUPER does - exports the spots to two different programs.
I did as you say below, except that the DX Hunter link link is
C:\DXTELNET\DUPER\ and when you run DUPER, enter the 2 paths:
C:\DXTELNET\DXT2WL\
C:\DXTELNET\DXT4WIN\
and the spots will flow to both programs! Too much fun! Guys, if you
haven't tried DX Telnet, it's great. Lots of filtering options, ability
to connect to multiple clusters - RF and Internet, and it will even page
you with that DX spot you're waiting for while shopping for the Xmas
tree with the XYL! Cudos to Fab and the DX4WIN and Writelog authors!
73
------------------------------------------------------------
WA9ALS - John
email: jfleming@shelbynet.net
homepage: http://www.qsl.net/wa9als
logbook: http://www.qsl.net/wa9als/search.htm
----- Original Message -----
From: "John Lawler" <Lawler@terragon.com>
To: <dx4win@qth.net>
Sent: Wednesday, December 06, 2000 3:55 AM
Subject: [DX4WIN] DXTelnet
> I did manage to successfully link the DXTelnet spots to DX4WINspot
> window....Credit goes to the DXTelnet author,IK4VYX and to
John,WA9ALS,who
> responded to the REFLECTOR.
> Background: DXTelnet is a telnet program that can run multiple
clusters via
> the internet, filter them by desired frequency and integrate the
resulting
> dx spots into our own DX4WIN software. All DX4WIN features are
> retained(radio control etc.)but you turn off the internal cluster
gathering
> in order to receive the alternate spotting source, DXTelnet.
> References:
> DXTelnet version 4.91
> www.ping.be/on4aoi/dxt.shtml Instructions: I will note exceptions to
this
> web site that are
> confusing
> 1) Upsend is only needed for networked computers, skip upsend exe
> initialization
> 2) Set DXTelnet path as shown, Ignore reference to dx hunter,set dde
> link,topic and item as shown. Enable the link.
> 3) DX4Win setup is correct as shown, I used the first handshake
> 4) You don't need to run udpsend.exe as noted for a one computer
setup.
> 5) I created a short cut for DXT4WTN.exe, found in the path described
in #2
> above, This launches DXTelnet<>DX4WIN window.This window shows the
spots
> coming from DXTelnet and
> going to DX4win.Your DX4WIN spot window may be filtered to only show
your
> needed countries so look at this DXTelnet<>DX4WIN window to determine
if
> spots are linking
> 6) Setting paths (#2 above): DXTelnet will not accept long path names.
>
> Good Luck, Hopefully this exercise will be worth the additional spot
> capability.
>
> John, N7EB
>
>
--
WWW: http://www.writelog.com/
Submissions: writelog@contesting.com
Administrative requests: writelog-REQUEST@contesting.com
Problems: owner-writelog@contesting.com
|