VHFcontesting
[Top] [All Lists]

Re: [VHFcontesting] [TowerTalk] 12V DC Rotor Control Options for VHF Rov

To: "James Gordon Beattie, Jr." <w2ttt@att.net>, "vhfcontesting@contesting.com" <vhfcontesting@contesting.com>, Towertalk Reflector <towertalk@contesting.com>
Subject: Re: [VHFcontesting] [TowerTalk] 12V DC Rotor Control Options for VHF Rover Station
From: Mike Fahmie via VHFcontesting <vhfcontesting@contesting.com>
Reply-to: Mike Fahmie <wa6zty@yahoo.com>
Date: Sat, 20 Aug 2016 17:01:22 +0000 (UTC)
List-post: <vhfcontesting@contesting.com">mailto:vhfcontesting@contesting.com>
Are you looking for something to run on 12VDC or 110VAC?  The HAM series rotors 
run on low voltage AC so a simple (basic function) AC powered controller would 
be fairly easy, but a DC powered unit would require that AC voltage be 
generated with either an 'over the counter'  AC inverter or additional 
circuitry in the controller.
-Mike-


 
      From: "James Gordon Beattie, Jr." <w2ttt@att.net>
 To: Mike Fahmie <wa6zty@yahoo.com>; "vhfcontesting@contesting.com" 
<vhfcontesting@contesting.com>; Towertalk Reflector <towertalk@contesting.com>  
Sent: Saturday, August 20, 2016 9:16 AM
 Subject: Re: [TowerTalk] 12V DC Rotor Control Options for VHF Rover Station
   

| Mike et al,Anyone build something for a CDR HAM-series rotator and can point 
to some documentation?73,Gordon Beattie, W2TTT201.314.6964

Sent from AT&T Mail on Android 
|  From:"Mike Fahmie via TowerTalk" <towertalk@contesting.com>
Date:Fri, Aug 19, 2016 at 21:22
Subject:Re: [TowerTalk] 12V DC Rotor Control Options for VHF Rover Station

 I was able to build a fairly simple 12V controller for my G800.  Two 
pushbutton switches (cw/ccw) and a cheap EBAY digital display (bearing).  Runs 
nicely on 12V but if you boost it to 18V it turns faster.  Lacks fancy features 
but turns the antenna and indicates bearing.  More info on request.
-Mike-WA6ZTY

 
      From: Mark Adams <msadams60@gmail.com>
 To: vhfcontesting@contesting.com; "towertalk@contesting.com" 
<towertalk@contesting.com> 
 Sent: Friday, August 19, 2016 5:27 PM
 Subject: [TowerTalk] 12V DC Rotor Control Options for VHF Rover Station
  
Hi Gang,

I just tried to purchase an MDS RC1-Y to use with my Yaesu 800DXA rotor.
SURPRISE! The order was cancelled and they refunded my money. Hmmmm.
Assuming this is not just an oddball mistake, I now need to find a DX
powered box to get my rover rebuild back on track. I see that DX
Engineering has a unit by EA4TX, but that is about all.

Are there any other easy options? I guess I could just buy a sine wave
inverter and a regular box, but my rover has no need for AC. Well, a Keurig
would be nice I suppose :-)


-- 
73, Mark K2QO
FN03ra
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


  
 
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
 |

 |



   
 
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
<Prev in Thread] Current Thread [Next in Thread>