Well, the price is right!
I built the 6m beam from scratch. I think it cost about $40 in parts.
73, Zack W9SZ
On Fri, Jun 17, 2016 at 1:24 PM, Mary Brown <maryalanab@gmail.com> wrote:
> Why not go with one of these?
> http://www.staples.com/Channel-Master-Telescoping-Antenna-Mast-15ft/product_2089811?cid=PS:GooglePLAs:2089811&ci_src=17588969&ci_sku=2089811&KPID=2089811&gclid=CNe8h57Xr80CFRCRaQodEvYG5g
> with what an antenna costs why risk the damage from something flimsy.
>
> -----Original Message-----
> From: VHF [mailto:vhf-bounces@w6yx.stanford.edu] On Behalf Of Zack Widup
> via VHF
> Sent: Friday, June 17, 2016 1:17 PM
> To: VHF Contesting Reflector; VHF REFLECTOR
> Subject: Re: [VHF] Telescoping mast
>
> I've received quite a few replies from people about this. Thanks to all of
> those who replied!
>
> Several people have said they have used EMT pipe as masts, and quite a few
> people have told me not to use it because it bends easily. A few people
> recommended fiberglass and a few said not to use fiberglass. So I'm not
> completely sure which way I'm going to go, but I didn't say in my original
> posting what I wanted it for.
>
> I have been doing portable operations for many years using the Radio Shack
> stackable 5-foot long steel mast sections. I have used these to put up
> antennas up to 20 feet using a very simple tilt-over base. I have no
> problem with that arrangement with Yagis for 144 MHz and up. But my 6 meter
> beam is unwieldy. It is four elements on a 13 foot boom. It's difficult for
> me to put it up by myself using a tilt-over base. It's difficult to balance
> one end of the beam on the ground while fastening it to the mast and
> raising it. Once a strong wind caught the antenna and tilted it as I was
> putting it up, snapping off half of the reflector.
>
> So I figure if I can mount some sort of telescoping mast vertically and
> use that to push up the 6m beam, there is less risk of damaging it.
>
> I'm trying to keep the cost down, so I'm looking into aluminum tubing
> sections that nest into the next size up.
>
> 73, Zack W9SZ
>
>
> On Mon, Jun 13, 2016 at 10:51 AM, Zack Widup <w9sz.zack@gmail.com> wrote:
>
> > Hi, does anyone here have any experience with building a telescoping
> > mast out of EMT pipe sections? Specifically the 1.25, 1.5 and 2 inch
> O.D. pipes.
> >
> > I'm thinking of making something with them for portable and rover
> > operations.
> >
> > 73, Zack W9SZ
> >
> >
> >
> > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_
> > campaign=sig-email&utm_content=webmail&utm_term=oa-2322-b>
> > Virus-free
> > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_
> > campaign=sig-email&utm_content=webmail&utm_term=oa-2322-b>
> > <#m_-1347973621022782885_DDB4FAA8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
> >
> _______________________________________________
> VHF mailing list
> VHF@w6yx.stanford.edu
> https://w6yx.stanford.edu/mailman/listinfo/vhf
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
>
>
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=oa-2322-a>
Virus-free.
www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=oa-2322-a>
<#DDB4FAA8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting
|