Looks like Dave came up with the info on the PP units. I found my file which
contains a lot of what Kurt had copyrighted in 2005 and includes adapter
plates, small, medium and some info on the large and extra large motors. What I
have is a small, a large and two extra large PP motors which according to Kurt
would be good for turning the whole tower. In the late 50's I used the small
one on top of a power pole with a homemade gear driving a selsyn for direction
indication.
73Bob K6OSM
In a message dated 3/18/2024 4:58:59 PM Pacific Standard Time,
leeson@earthlink.net writes:
For a start, see
https://web.archive.org/web/20200711193004/https://k7nv.com/notebook/ppinfo/
See also
https://ve3vn.blogspot.com/2015/11/choices-on-adapting-prop-pitch-motors.html:
"On a bench test one drew 8 A and the other drew 7 A at 24 VDC."
An interesting idea for using series resistors to reduce startup surge
is at http://www.bigskyspaces.com/w7gj/NewMotor.htm
See also https://www.eham.net/reviews/view-product?id=5837 comments by
AC8DE: "I hadn't considered the high current required by a prop pitch
with a 280' wire run and how that affected voltage drop and wire gauge.
The minimum wire I could go with was 10 gauge, which causes a 10%
voltage drop at nominal current draw of 5 amps. At the peak amps of 8,
it hits 17%, but I expect that we will never see that because we will
keep the ramp rate pretty low."
Because my towers are some 400 feet from the shack, I built a remote
power setup at the tower with a transformer 24 volt supply and relays.
Because the motor is a DC type, the relays are wired to present a short
when not rotating, which acts as a brake. Kurt made me a special mast
connector with a rubber torque isolator (I have blueprints), which has
worked brilliantly in our storms with gusts over 120 mi/h. I run Romex
cable from the supply to the rotator.
See also
https://www.greenheronengineering.com/product/rotator-controller-prop-pitch/
https://www.greenheronengineering.com/product/prop-pitch-28vdc-motor-rpu/
http://www.zs6p.com/PPM_gearbox-sketches_and_notes.pdf
If I have more info, I'll dig it out and provide it. I had a physical
copy of the Section 12, Curtiss Wright 1943 Hollow Steel Blade Propeller
(3 Blade) Service Manual that I shared with Kurt K7NV, but I don't have
a scan. See
https://app.aircorpslibrary.com/document/viewer/11a5e262-f115-4949-bbe5-8d3ab3803e59
and https://www.ebay.com/itm/275383055212
73 de Dave, W6NL/HC8L
On 3/17/24 6:40 PM, Bob via TowerTalk wrote:
> Hi Norm,
> This is Bob Schaefer K6OSM and I used a PP motor on a Hornet tri-band beam
> back in the late 50's. I will look in my files to see what I can find on
> these motors. I do recall that the elapsed time for a complete turn was close
> to a full minute. I live in Gardnerville and Kurt lived in the adjoining town
> of Minden, I never made personal contact with Kurt but exchanged info with
> him when I lived in Idaho. I still have four PP motors and will see if I can
> find anything that will help you.Bob K6OSM
> In a message dated 3/16/2024 10:29:49 PM Pacific Standard Time,
> npalex@bellsouth.net writes:
> Hopefully there are some TowerTalk participants that are using PropPitch
> rotor systems. I am looking for some operating characteristics relating to
> supply voltage, currents and rotation speed (time to do 360*). I have been a
> prop pitch user for many years and my 'go to' in the past on such questions
> would be Kurt K7NV now SK or Joel K2QVB also a SK. My prop pitch dates back
> to W0MLY Dick Mckercher, DXer of the 50's and 60' and creator of Antenna Mart
> products. That is the background - Specifically I am look for the DC voltage
> at the 'controller' and the voltage underload at the PP motor. What is the
> 'start-up' surge current and the steady state 'run' current. Those using
> Kurt's Green Heron controller, results may be different as it supplies is PWM
> ramp up and down, but the 'run' levels will be "DC" and useful data. Finally
> is there anyone who has the working knowledge of Prop Pitch assemblies, or
> maybe have access to the information that Kurt accumulated the could be made
> available us PropPitch users?Looking for some help --Norm W4QN | |
> Virus-free.www.avast.com | _______________________________________________
> _______________________________________________TowerTalk mailing
> listTowerTalk@contesting.comhttp://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|