Towertalk
[Top] [All Lists]

Re: [TowerTalk] Rotor control line MOV's

To: George Skoubis <geo.skoubis@gmail.com>, Tower Talk <TowerTalk@contesting.com>
Subject: Re: [TowerTalk] Rotor control line MOV's
From: Raymond Benny <rayn6vr@gmail.com>
Date: Wed, 25 Aug 2021 22:57:34 -0700
List-post: <mailto:towertalk@contesting.com>
Dave,

I have had to replace several of the MOV's in Green Heron
rotator controllers. I called Green Heron in the past and ordered several
extra to have on hand. One is labeled as 1.5KE82CA. Here is a link to
Mouser Electronics:
https://www.mouser.com/ProductDetail/Littelfuse/15KE82CA?qs=2VFNtWizgidzIX%252bPe5AWEA%3D%3D

The second one, and I don't know the difference between them, is labeled
1404 1.5KE20CA. The Mouser link is:
https://www.mouser.com/ProductDetail/Littelfuse/15KE20CA?qs=zHiv0nsVGmo72eE9eQTsNw%3D%3D

 Unlike other large parts outfits, Mouser does not have a minimum order
amount.

You can check the Mouser data sheets further, I did not. You might call
Green Heron and see what they say and perhaps you could purchase some from
them.

Hope this helps.

Ray,
N6VR/W7YA




On Wed, Aug 25, 2021 at 10:38 AM George Skoubis <geo.skoubis@gmail.com>
wrote:

> I’ve bought the ones Chris / KF7P mentioned for Rotor control lines and
> also for the relay lines to antenna switches and stack matches.  I think I
> have 4 of them.
>
>   I haven’t had a direct hit but I haven’t had anything fail either.
>
>   I purchased them from his website (along with other grounding and tower
> products) and have been very satisfied.
>
>   Be sure to buy the ones that match the voltage range of your equipment.
>
>   No relationship except other than a happy customer.
>
> George / W7GES
>
> > On Aug 25, 2021, at 8:51 AM, chris perri <EZRhino@fastmovers.biz> wrote:
> >
> > These:
> >
> > https://surgestop.com/surge-products/m-348.html <
> https://surgestop.com/surge-products/m-348.html>
> >
> > Chris
> > KF7P
> >
> >
> >
> >> On Aug 24, 2021, at 8:47 PM, R. David Eagle via TowerTalk <
> towertalk@contesting.com> wrote:
> >>
> >> Im looking to add some surge protection on my rotor control wires and
> was wondering if anyone has any input as to which ones work the best?
> Source and part numbers would be appreciated!
> >> Thanks,
> >> DaveKB8NNU
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>