HUH???? The g-800/1000/2700/2800SDX series going back to at least the 1980's
were all dc drives
David Robbins K1TTT
e-mail: mailto:k1ttt@arrl.net
web: http://wiki.k1ttt.net
AR-Cluster node: telnet://k1ttt.net:7373
-----Original Message-----
From: TowerTalk <towertalk-bounces@contesting.com> On Behalf Of Jack Brindle
via TowerTalk
Sent: Friday, August 6, 2021 16:07
To: Towertalk <towertalk@contesting.com>
Subject: Re: [TowerTalk] Yaesu contol box?
It happened long before 2019. My G-1000DXA from the 2000’s is a DC device.
Schematics for the controllers and rotors are on-line and available.
73,
Jack, W6FB
> On Aug 6, 2021, at 1:47 PM, Grant Hopper <kb7wsd@gmail.com> wrote:
>
> There is one "gotcha" to all this. In 2019, Yaesu changed to using DC on
> the rotors. From DX-Engineering " Instead of the usual AC motor drive
> used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA
> use a variable-voltage DC motor, removing the need for a large
> starting capacitor with its potential for failure exposed to outside
> temperature variations.
> " The 450 and the 5500 are the same way.
>
> There might be an easy way to determine the AC vs DC upon inspection.
> I haven't looked at all the manuals to confirm this but at least with
> the 450, it uses only four wires for DC types. Otherwise, some of the
> models are stamped with a "DC" after the model number eg. " For
> clarity, the new DC rotator motors are marked "G-450DC" at the
> connector. The rear panel of the controller is titled "G-450ADC" on the
> serial number label."
>
> 73,
> Grant
> KB7WSD
>
> On Fri, Aug 6, 2021 at 8:55 AM <k1ttt.dave@gmail.com> wrote:
>
>> Well, yes, kinda, maybe in a pinch.... all the boxes use the same 5
>> pins for motor power and indication, so yes, they can all be used if
>> needed to power each other... HOWEVER, the 2700 and 2800 use the 6th
>> pin to detect when it is getting near the end of travel to invoke an
>> auto slowdown to keep the more powerful motor and likely heavier
>> antenna from hitting the hard stop too hard.
>>
>> David Robbins K1TTT
>> e-mail: mailto:k1ttt@arrl.net
>> web: http://wiki.k1ttt.net
>> AR-Cluster node: telnet://k1ttt.net:7373
>>
>>
>> -----Original Message-----
>> From: TowerTalk <towertalk-bounces@contesting.com> On Behalf Of
>> k7lxc--- via TowerTalk
>> Sent: Friday, August 6, 2021 11:35
>> To: towertalk@contesting.com
>> Subject: [TowerTalk] Yaesu contol box?
>>
>> Howdy, TowerTalkians -
>>
>> Are Yaesu control boxes interchangeable? Since they all have the
>> same wiring, I'm thinking that they can all work with other Yaesu rotators.
>> Is
>> this right? Tnx. Cheers,Steve K7LXC
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|