Towertalk
[Top] [All Lists]

Re: [TowerTalk] Connector on 7/8 Heliax

To: "'Clay Autery'" <KY5G@montac.com>, <towertalk@contesting.com>
Subject: Re: [TowerTalk] Connector on 7/8 Heliax
From: "Gene Smar" <ersmar@verizon.net>
Date: Thu, 9 Aug 2018 21:46:22 -0400
List-post: <mailto:towertalk@contesting.com>
Also consider giving Joel at The RF Connections (www.therfc.com )  a call.

73 de
Gene Smar  AD3F


-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Clay 
Autery
Sent: Thursday, August 09, 2018 9:25 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Connector on 7/8 Heliax

Love those folks!!  Buy everything I can from there.

73,

______________________
Clay Autery, KY5G
(318) 518-1389

On 09-Aug-18 20:12, Jim wrote:
> I've always had good luck with Tessco over the last 25 years.
>
> 73
> Jim W7RY
>
>
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of 
> Doug Ronald
> Sent: Thursday, August 9, 2018 2:12 PM
> To: 'towertalk' <towertalk@contesting.com>
> Subject: Re: [TowerTalk] Connector on 7/8 Heliax
> Importance: Low
>
> For anyone considering either of these two vendors for a jumper cable 
> fabricator, I can give my feedback on their initial performance. After 
> issuing a specification for my cable to both via email, I got a terse 
> reply back from Tally. I then asked how to get the project going, and no 
> response.
> Issuing the same spec to Tessco, they set me up with an account, and 
> have promptly issued a quote, which I have accepted.
> The only downside to Tessco so far, is they were unable to perform a 
> pressurized leakage test. I'll be anxious to see the finished jumper...
> -Doug Ronald, W6DSR
>
> -----Original Message-----
> From: Jim W7RY [mailto:jimw7ry@gmail.com]
> Sent: Tuesday, June 12, 2018 17:07
> To: Doug Ronald, W6DSR <Doug@DougRonald.com>; 'towertalk'
> <towertalk@contesting.com>
> Subject: Re: [TowerTalk] Connector on 7/8 Heliax
>
> Tessco provides made up Heliax assemblies.
>
> www.tessco.com
>
> There is also Tally. www.tallycom.com
>
>
>
>
> Thanks
> 73
> Jim W7RY
>
>
> -----Original Message-----
> From: Doug Ronald, W6DSR
> Sent: Tuesday, June 12, 2018 6:50 PM
> To: 'towertalk'
> Subject: Re: [TowerTalk] Connector on 7/8 Heliax
>
> Air because the antenna's 1 5/8 EIA transmission line is pressurized. 
> I already have the nitrogen setup for that outdoors at the antenna's 
> base, but I can put the tank inside where it belongs if I have 
> pressurized helix as well.
>
> Actually if I buy a ready-made cable, I'll have a 1 5/8 EIA flange on 
> one end, and a 7/16 DIN into the shack on the other. Then I can get 
> rid of the EIA-to-N adapter at the antenna base.
>
> We're just talking HF. The antenna is rated 3 -- 30 MHz. I want low 
> loss transmission line to maintain my hard-fought noise figure at the 
> upper end toward 30 MHz. Since I'm on solar power, I'll be lucky to 
> even get 1500 Watts out, but the EIA stuff is the way the antenna 
> came, and I'm stuck with it.
>
> So you guys have any suggestions on a good place to pick for the 
> transmission line? I see Commscope, maybe RFParts, Pasternack, but 
> what others are out there?
>
> Thanks for responding,
> -Doug
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of 
> Jim W7RY
> Sent: Tuesday, June 12, 2018 03:54 PM
> To: towertalk <towertalk@contesting.com>; Steve Maki 
> <lists@oakcom.org>
> Subject: Re: [TowerTalk] Connector on 7/8 Heliax
>
> My question as well.
>
> You WILL have to pressurize it.  How long a run at what frequency are 
> we talking about here Doug?
>
>
>
> Thanks
> 73
> Jim W7RY
>
>
> -----Original Message-----
> From: Steve Maki
> Sent: Tuesday, June 12, 2018 5:08 PM
> To: towertalk
> Subject: Re: [TowerTalk] Connector on 7/8 Heliax
>
> Why are you leaning toward air cable? What's your application?
>
> -Steve K8LX
>
> On 06/12/18 16:42 PM, Doug Ronald, W6DSR wrote:
>
>> Well, okay, if I have to start from scratch, I'm looking at 
>> Commscope's
>> HJ5-50 7/8" heliax or something equivalent. Since I'll be ordering a 
>> custom setup, I might as well upgrade to 7/16 DIN connectors.
>>
>> So my new question is what vendor do the folks here recommend to make 
>> up my custom cable?
>>
>> Thanks,
>> W6DSR
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>