Dick,
Tnx for the info.
I sent a note to Davis RF about their stripping tool also. Will take a
closer look at the RFA-4087 too.
I only use either hardline, Buryflex or 9913 that still looks like new after
35 years. I want all coax to be 100% shielded. Found it helped reduce
significantly ingress of noise.
It seems for stripping, Buryflex and 9913 are about the same.
So far I have been using MGS 7505-400 PL-259's. I plan on also getting some
RFU-507-SI connectors to compare.
By the way I found if I lightly tin the Buryflex center conductor I don't
squish any strands and all the strands go into the center pin. Guess how I
found out I was periodically squishing a few strands.
73,
N2TK, Tony
-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Dick
Green WC1M
Sent: Saturday, February 04, 2017 3:17 PM
To: 'N2TK, Tony' <tony.kaz@verizon.net>; towertalk@contesting.com
Subject: Re: [TowerTalk] Coax stripping tool for crimp connectors
I use this stripper from RF Industries for Bury-FLEX:
http://rfsearch.rfindustries.com/drawings/RFA-4087.pdf
It's adjustable, so it'll work on any pretty-much any 1/2" coax.
You can buy one here:
https://www.rfparts.com/tools/tools-strippingmanual/rfa4087.html
You have to be careful to match the crimp connector to the cable type. I
use these for Bury-FLEX UHF crimp connectors:
https://www.rfparts.com/rfu507-si.html
drawing with strip dimensions and recommended crimp die sizes:
http://rfsearch.rfindustries.com/drawings/RFU-507-SI.pdf
With Bury-FLEX you have to be careful not to bend, kink or spread the
exposed center conductor -- it's a very tight fit. Usually I have to twist
the jacket/foam plug left by the stripper as I remove it from the cable,
which tightens the center conductor. Might be worth inquiring whether RF
Industries (or anyone else) makes a UHF crimp connector that has a slightly
larger center conductor shaft.
I use these for Bury-FLEX N crimp connectors:
https://www.rfparts.com/rfn1006-3i.html
drawing with strip dimensions and recommended crimp die sizes:
http://rfsearch.rfindustries.com/drawings/RFN-1006-3I.pdf
I find these much easier to install than the UHF crimp connectors.
The notes on both drawings aren't very clear about whether to crimp or
solder the center conductor. My interpretation is that you can crimp cables
with larger center conductors, like Buryflex, LMR-400, 9913, etc., but
should solder cables that have smaller center conductors, like RG8/U. If you
choose to solder the N connector, don't solder through the small hole in the
shaft. That's just to make sure the cable is fully inserted. If you solder
there the pin might not snap into the connector. Solder the pin at the base
where the center conductor enters.
FWIW, I always solder the UHF center conductor and always crimp the N center
conductor.
Note that rfu507-SI and rfn-1006-3I connectors are in the Davis RF list of
connectors recommended for Bury-FLEX.
73, Dick WC1M
-----Original Message-----
From: N2TK, Tony [mailto:tony.kaz@verizon.net]
Sent: Saturday, February 4, 2017 1:20 PM
To: towertalk@contesting.com
Subject: [TowerTalk] Coax stripping tool for crimp connectors
Does anyone offer a coax stripping tool to prepare Buryflex for PL-259 crimp
connectors? The DX Engineering coaxial cable stripping tool does a nice job
for solder connectors. Looking for something like that for crimp connectors.
73,
N2TK, Tony
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|