Dale M Schwartz
SCHWARTZ POSEL IMMIGRATION LAW GROUP
Immigration & Naturalization Law
Suite 450 RiverEdge One
5500 Interstate North Parkway, NW
Atlanta, GA 30328
Tel: (770) 951-1100
Fax: (770) 951-1113
Dale@immlawfirm.com
www.immlawfirm.com
PAST PRESIDENT: American Immigration Lawyers Association
ADJUNCT PROFESSOR: Emory University School of Law
> On Nov 18, 2016, at 12:00 PM, "towertalk-request@contesting.com"
> <towertalk-request@contesting.com> wrote:
>
> Send TowerTalk mailing list submissions to
> towertalk@contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/towertalk
> or, via email, send a message with subject or body 'help' to
> towertalk-request@contesting.com
>
> You can reach the person managing the list at
> towertalk-owner@contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TowerTalk digest..."
>
>
> Today's Topics:
>
> 1. Re: Yaesu G-8000 DXA controller with G-450 rotor
> (Herbert Schoenbohm)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 18 Nov 2016 12:48:34 -0400
> From: Herbert Schoenbohm <herbs@vitelcom.net>
> To: K0DAN <k0dan@comcast.net>, towertalk@contesting.com
> Subject: Re: [TowerTalk] Yaesu G-8000 DXA controller with G-450 rotor
> Message-ID: <5d347132-e88a-ac05-abce-1cce8ccb9e5a@vitelcom.net>
> Content-Type: text/plain; charset=windows-1252; format=flowed
>
> Thanks Dan as I am starting to get somewhere with this. All the cable
> pins seem to match but Ii will do some more comparison of the two
> circuits to make sure. Although Pin #1 on the G-800DXA is there I seen
> no mention of it on the 450. I think it is voltage going upstairs to
> the rotation pot however.
>
> Herb, KV4FZ
>
>
>> On 11/18/2016 11:53 AM, K0DAN wrote:
>> http://bama.edebris.com/manuals/
>>
>> -----Original Message----- From: Herbert Schoenbohm Sent: November 17,
>> 2016 20:50 To: K0DAN Subject: Re: [TowerTalk] Yaesu G-8000 DXA
>> controller with G-450 rotor
>> Thanks for info Dan. Can you send me the link for BAMA as this site
>> is not known to mr?
>>
>>
>> Thanks, Herb
>>
>> KV4FZ
>>
>>
>>> On 11/17/2016 3:56 PM, K0DAN wrote:
>>> I am pretty sure the G450 is not interchangeable with the G-800,
>>> G1000, and G2800 controllers. However, the G800, G1000, and G2800 can
>>> be interchanged. And, with suitable connector changes or use of a
>>> pigtail, the SDX and DXA versions can also be swapped.
>>>
>>> The schematics are on BAMA, and you can compare where the units are
>>> similar/different.
>>>
>>> GL es 73
>>> dan
>>> k0dan
>>>
>>> -----Original Message----- From: Herbert Schoenbohm
>>> Sent: November 17, 2016 07:36
>>> To: towertalk@contesting.com
>>> Subject: [TowerTalk] Yaesu G-8000 DXA controller with G-450 rotor
>>>
>>> I have an orphan Yaesu G-8000DXA controller and would like to know if I
>>> can replace by G-450A control box with it without any modification?
>>> The plugs are the same and from the schematic the control circuit is
>>> similar. But I would like to know first before I brick the rotor on the
>>> tower. Please help.
>>>
>>>
>>>
>>> Herb Schoenbohm, KV4FZ
>>>
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
> ------------------------------
>
> End of TowerTalk Digest, Vol 167, Issue 45
> ******************************************
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|