I agree, Bob. That person's response was smug.
As shown by his responses today and many times
in the past, he is the one with the attitude that needs
correction. Apparently, from private emails I've
received today and in the past, I'm not alone in my view.
Yes, my decades of experience, both personal
and professional in radio & electronics. hihi
The other person you mentioned (WB5UAA) is
another matter. You're entitled to your differing
opinion.
Now, if the attempted public humiliation of me is
done, let's get back to TT. I agree with Hank W6SX.
vy 73,
Bryan WA7PRC
Date: Tue, 10 May 2016 16:15:58 -0700
From: Bob K6UJ
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Soldering Iron, Connectors, Cable
Bryan,
What a smug response.
Your decades of experience.....hihi
This might come as a shock to you but there are members here that
actually have more experience
than you and more importantly have more technical knowledge than you.
Lose the attitude and help us support one another.
Bob
K6UJ
You chased Guy, WB5UAA off the EHAM antenna forum with your
On 5/10/16 2:31 PM, Bryan Swadener via TowerTalk wrote:
> I apologize for presenting my opinion.
> Clearly, someone knows better than I.
> My decades of experience must mean
> nothing.
>
> Bryan WA7PRC
>
> Date: Tue, 10 May 2016 13:52:50 -0700
> From: [Deleted]
> To: towertalk@contesting.com
> Subject: Re: [TowerTalk] Soldering Iron, Connectors, Cable
>
> On Tue,5/10/2016 1:18 PM, Bryan WA7PRC via TowerTalk wrote:
>> The idea that only Amphenol produces good quality connectors is
>> not correct. There are others. DX Engineering supplies top-shelf
>> connectors and adapters at reasonable cost.
> Unless you are in the position of a mfr or vendor to buy and test
> samples from known mfrs, or have worked for a mfr who has done that,
> you're in no position to know whether a mfr's product is good or not,
> let alone "top shelf." The electronic products I've seen from DXE are of
> good quality, but I've not seen their connectors or cables.
>
>> Others have touted The RF Connection as a source of good quality connectors
>> at reasonable cost.
> That may be, but they sell a lot of JUNK connectors too. When I got back
> on the air around 2003, I filled my parts box with 5-10 each of the 5-8
> pin DIN connectors they were selling. They were junk -- metal that
> wouldn't take solder, dielectric that melted under minimal heat from a
> good iron.
>
> In the same time frame, I also stocked up on lots of low cost coax
> connector adapters, barrels, elbows, and Tees at Chicago area hamfests,
> typically paying $2-$4 each. In the four years that followed, I learned
> the hard way that those connectors were JUNK -- they fell apart,
> overheated, went intermittent, and outright failed -- each time causing
> me lots of grief in troubleshooting the problem. A $12 connector or
> adapter seems expensive, until you've crawled through an attic, along a
> coax run, or climbed a tower to find a $4 piece of junk.
>
>> They seem to have a wide selection.
> Yes. They also sell Amphenol, and a broad selection of hard line
> connectors they have been able to find. But I will no longer do biz with
> them because I learned that they pulled what I consider to be a very
> dirty trick on their employee who I dealt with on a large group
> purchase several years ago.
Date: Tue, 10 May 2016 16:22:30 -0700
From: Hank W6SX
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Soldering Iron, Connectors, Cable
Hey everyone.
Criticize in private, praise in public.
Technical, non ad hominem, commentary always welcome of course.
73,
Hank, W6SX
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|