Always plan on allowing for expansion.
The only real drawback with automatically operated remote switches over
manual is cost. Hookup may, or may not be more complex. It's usually,
follow the directions.
The nice thing about a decoder and a controller is it will pick the
proper antenna for you (once it is properly connected). The odds of the
wrong antenna using manual switches, even properly labeled are quite
high. IOW, it becomes a question of when, not if you transmit into the
wrong antenna. Yes, I know there are those who say they have used that
scheme for years without a problem, but according to the odds they are
the lucky exception rather than the rule.
I trust computers only after a program has proven itself. The same goes
for all the connection. There is the old saying, "To err is human, but
iy takes a computer to really screw up" USUALLY a computer program is
thoroughly proven by the time it gets to the public, but there have been
some notable screw-ups in operating system updates.
Another point about the remote selecting switches is they easily allow
for adding antennas to the system. They do not have to be monobanders.
20, 15, and 10 can all selected as the same antenna with most systems.
My rig allows selecting a particular output for each band. My six pack
has remote switches connected to two of the outputs. That means few of
those connections identified with a band actually are used for that band.
NOTE: If you end up with any unused connectors (IE SO239s) lightly
lubricate the threads and use a plastic cap to cover the connector. If
not properly weather proofed the silver plated connectors will rapidly
deteriorate. I've had them become unusable in just a few months.
73
Roger (K8RI)
On 4/18/2016 Monday 6:47 AM, Earl Morse wrote:
For simple as possible, skip the remote switches. Run all the coaxes into the
shack. Have a 4 to 6 way coax switch on each radio. Use 2 way switches to
switch the more popular antennas between either radio. It is manual operation
but you probably have everything laying around the shack to put it together now.
While having the ability to switch any antenna between either radio and having 2
antennas for each band is nice you will find that for SO2R you tend to have a
primary radio and a secondary radio. Primary is going to be running on the most
productive bands with the best antennas while the secondary radio is going to be
S&Ping on the off bands with whatever antennas you have left over, most likely
the next band up or down from the run radio. The important bands of interest are
going to change depending on the contest. In most cases, propagation will make
bands mutually exclusive of each other. For example, you won't need 160/80M during
the day when 20-15-10M is hopping, and vice-versa. So being able to switch any
antenna to any radio at any time probably isn't needed.
Run it manually for a while and you will figure out exactly what you need.
Earl
N8SS
------------------------------
Message: 6
Date: Sun, 17 Apr 2016 19:13:51 -0400
From: "Douglas Ruz / CO8DM"<co8dm@frcuba.co.cu>
To: "Towertalk"<towertalk@contesting.com>
Subject: [TowerTalk] 6 x 2 unit...
Message-ID:<00d701d198fe$d1ef96b0$75cec410$@co.cu>
Content-Type: text/plain; charset="us-ascii"
Hi,
I am building a simple as possible SO2R configuration.
I need some advices about a 6 x 2 antenna relay unit.I prefer a kit because
it is cheaper.
I think I need build also a Band decoder.any idea?
Thanks,
Doug, CO8DM
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
--
73
Roger (K8RI)
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|