I suppose with some trig you could figure the total projected area
at various wind angles. One going down and one going up. Would some
angle that gives equal projected area from each figure be the max?
You don't need to be concerned with equal areas. The force (load) on
the element will be broadside to the element and will vary with the
angle of the wind to the element. The force (load) on the boom will
be broadside to the boom and vary with the angle of the wind to the
boom. Those forces add as a vector sum which is maximized when the
wind is at 45 degrees to the boom/elements.
The area of largest force is:
sin(45) * (2.88 + 2.76) + cos(45) * (3.67 + 1.24 + 1.20)
= 0.707 * (5.64) + 0.707 * (6.11)
= 8.31 sq. ft.
The boom value will need to be increased somewhat to account for a boom
to mast plate and the element values increased to account for element
mounting hardware, particularly if the original U channel is used. I'd
allow between 8.5 and 9 sq. ft in any tower/mast loading calculation.
73,
... Joe, W4TV
On 4/10/2016 12:51 AM, Ken K6MR wrote:
I’ve wondered this myself but never bothered to model it. Here are some rough
figures from Yagi Stress:
Reflector element without the tee: 2.88 sq ft.
Driven element without the tee: 2.76 sq. ft.
Reflector tee (each): 0.62 sq. ft.
Driven tee (each) 0.60 sq. ft.
Boom: 3.67 sq. ft.
Now the hard part: how do they add? I’m an EE so my logic may be totally flawed. YS
doesn’t allow for the tees in a single model so I can’t have it do everything at once.
Since the tees are parallel with the boom, I would think you would just add the
area of the tees to the area of the boom which should be the projected area
with the wind blowing 90 degrees to the antenna.
That would give 6.11 sq. ft. for that case. Wind straight on would be just the
elements: 5.64 sq. ft.
I suppose with some trig you could figure the total projected area at various
wind angles. One going down and one going up. Would some angle that gives equal
projected area from each figure be the max?
My first one is built from scratch and mounted to the side of the tower so I wasn’t
concerned with wind area. The XM240 is at the top of a mast so when I convert that one
I’ll have to be more careful.
Ok you mechanical types: does this look reasonable??
Ken K6MR
From: Kevin Stover<mailto:kevin.stover@mediacombb.net>
Sent: Friday, April 8, 2016 19:18
To: towertalk@contesting.com<mailto:towertalk@contesting.com>
Subject: [TowerTalk] W6NL 40m Moxon
I need to figure out the wind area of the W6NL 40 Moxon antenna.
The antenna starts like as a Cushcraft XM-240 which they say is 5.5 sqft.
The Moxon is going to be more but how much? I'm guesstimating 8 sqft.
--
R. Kevin Stover
AC0H
ARRL
FISTS #11993
SKCC #215
NAQCC #3441
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|