OK, but... Has anyone actually measured the Q of any modern traps? I have a
KLM-KT34A. Its linear loaded traps are supposed to have much less loss, but
while I cotton to the idea, I've never seen any measurements that show how much
difference there really is.
Kim N5OP
On Wednesday, April 15, 2015 6:02 AM, Jim Thomson <jim.thom@telus.net>
wrote:
Date: Tue, 14 Apr 2015 12:32:06 -0400
From: "Bry Carling AF4K" <bcarling@cfl.rr.com>
To: towertalk@contesting.com
Subject: Re: [TowerTalk] antenna choices for K4XS
What is your problem with metal enclosed traps?
Are you saying that they cause loss, like the RF going into a shorted turn and
heating
up the trap case instead of radiating RF energy? How many watts are you
guessing may be
turned into heat this way in the average beam trap?
Show us the maths please. You might be correct. I am not convinced so far.
Then there would also be the issue of your RF tank coil in a linear amplifier
being similarly
"metal enclosed." Somehow I am not seeing your point.
#### The capacitance between the al tube and the coil IS the capacitor.
Another way to build a trap
would be like how Telrex used to do it.... with a separate HT-50 / 58 style
NPO hv capacitor , wired
in parallel with the coil.
## Enclosing the coil with an aluminum tube drops the loaded Q of the coil
through the floor. Remember,
the 10M trap is a trap only on 10m. On 15 + 20m, the 10M trap is a coil
only. Ditto with the 15m trap,
the 15m trap is a coil when used on 20m. On 20m there is NO trap. The 20m ele
is way too physically short,
and its brought up to resonance by the 4 x coils from the 4 x traps per
element.
##If you are going to build a coil, the last thing you do is slide an aluminum
tube around it. Whether its from
the dreaded shorted turn effect or not is speculation. We must have had at
least a 1/2 doz Mosley TA-33 jrs
over the years..all with melted traps in the DE only. REF + DIR are not the
problem with power applied.
Mosleys standard fix for this is to use the larger DE traps from the 33 sr.
## when the trap covers were removed from the 33 jr DE traps, the polystyrene
grooved form inside, that the
small gauge aluminum wire is wound on..was completely melted ! It appeared as
though you had run a blow torch
back and forth across it. And these had melted during cold wx too. You would
think the aluminum tubing sticking out
each end of the trap would heatsink it a bit, but doesn’t. I noticed a
similar effect on hot 1/4 inch diam cu tubing coils
on linear amplifiers. Take a 20m tubing tank coil, and tap it for 15m. You
would think the un-used portion of the coil
would act as a heatsink for the used portion of the coil....it doesn’t. With
lid off, and using a dead cxr and footswitch,
I verified that effect myself. Portion of coil in use was extremely hot, and
just 1/2 inch further down the same coil, on the
other side of the tap, was barely luke warm...go figure.
## Sliding an al tube over a coil to make for a cheap and dirty capacitor is a
novel idea...... but makes for a lousy, low Q coil.
Telrex didn’t get it right either. The caps used would fail and blow out.
Dunno if it was cuz their RF current ratings were exceeded, or
if the peak V across em was too high...or both. HT-59s or series- parallel
HT-57s could be used, but then each trap would $100
in caps alone. 12 traps used in a 3 triband yagi.
## The other problem with most trapped yagis is they have foolishly stuffed
BOTH the 10m +15M trap inside the SAME aluminum
trap cover tube. On 15M band, the 10M trap is now a coil. The 15m trap
resides 1 inch away from the 10M trap. The now way
too physically short 15M ele now consists of the 10M loading coil and the 15m
trap. Lousy config imo. If you want to add a loading coil
to an ele, the optimum placement will be no more than half way out each ele
half. The further you place the coils out, the larger the required
inductance. You can see this effect in any software program that handles
loading coils for shortened dipoles etc. Placing the coils at the
extreme ends of the shortened dipole requires a huge amount of inductance.
## To do it right would mean separate 10 + 15m traps, with 10M trap being
located at aprx 1/4 wave from the boom. On15m,
the ele is now loaded..via the 10M coils. The 15m trap would then be located
< 1/4 wave from the boom. Telrex got that part
correct.
Jim VE7RF
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|