You might consider why building codes now require all outlets over bare
concrete to be GFI protected.
Grant KZ1W
On 1/20/2015 4:22 PM, Brian Carling wrote:
I suspect it's not as conductive as some may have us think...
Best regards - Brian Carling
AF4K Crystals Co.
117 Sterling Pine St.
Sanford, FL 32773
Tel: +USA 321-262-5471
On Jan 20, 2015, at 1:22 PM, David Robbins <k1ttt@verizon.net> wrote:
just remember when you do it to not use the point of an ohm meter probe.... it
is not easy to measure bulk material resistivity like in soil or concrete or
other types of materials.
you need to have some relatively large surface area to contact the material,
which is hard to do with already poured concrete.
Jan 20, 2015 12:59:36 PM, bcarling@cfl.rr.com wrote:
So far I am not convinced about using concrete. I'm going to do some resistance
testing on the concrete in my yard.
Best regards - Brian Carling
AF4K Crystals Co.
117 Sterling Pine St.
Sanford, FL 32773
Tel: +USA 321-262-5471
On Jan 20, 2015, at 10:13 AM, Grant Saviers wrote:
If your house slab was installed correctly with a vapor barrier and/or foam
insulation, then it is insulated electrically from earth.
Tower bases make good Ufers as do perimeter foundations, so my towers and shop
both had the rebar set as Ufers when constructed.
I also noticed that a new service transformer I had installed is set on a concrete
vault that has a ground stub cast into the side. The power company used it, no
ground rods. I'd estimate its surface area in contact with earth as more than 16 sq
ft. Compare that to less than 2 sq feet for a 10' 3/4" ground rod.
Grant KZ1W
On 1/19/2015 6:52 PM, Mike Reublin NF4L wrote:
The electrician I had (who does a LOT of grounding work here) come out to
connect my tower ground to the service ground told me he would be glad to drive
the extra rods extending out from the tower, but doing so would add no benefit
at all. I have no idea if this is true or not. At some point, lacking personal
knowledge, ya have to take someone's word for it. My tower megged out at 4 ohms.
Mike NF4L
On Jan 19, 2015, at 8:29 PM, Brian Carling
wrote:
The advice varies about this considerably. This week is the first time I've
even heard of UF ER or conductive concrete!
The professional experts that I know recommend putting a 20 to 30 foot ground
rod into the ground at each corner of your house and connecting heavy gauge
copper conductors up to lightning rodsup on the roof.
It seems like if the only thing you need is a large area of this allegedly
conductive concrete stuck in the ground, why not ground everything to the
concrete slab your house sits on!!
Best regards - Brian Carling
AF4K Crystals Co.
117 Sterling Pine St.
Sanford, FL 32773
Tel: +USA 321-262-5471
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|