Towertalk
[Top] [All Lists]

[TowerTalk] Anchor Bolts

To: <towertalk@contesting.com>
Subject: [TowerTalk] Anchor Bolts
From: "Wilson" <infomet@embarqmail.com>
Reply-to: Wilson <infomet@embarqmail.com>
Date: Wed, 15 Oct 2014 12:52:47 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
You will be mortified by the cost of 2.25" bolts and all that machining. Then you'd have to trim off the hex head. It would be a lot cheaper to buy barstock and drill and tap it for his existing bolts. But that tap is unusual and hard to use, so maybe using longer stock and threading the top part on a lathe would be the more economical solution.
You don't have an expensive anchor, so the epoxy would still be needed.
Come to think of it, how about just making a 2.25" bushing, through which he puts the original size bolt?? While it's in the lathe, cut aggressive grooves around the outside for lock in of the epoxy. Cheapest solution...mild steel or stainless fine, possibly from salvage, and minimal skill level.
Even I could do  it!
I'd also run a weld bead around the top and bottom of the bushing, where the bolt goes through, to guarantee no movement that could fatigue the epoxy. He could machine the hole a hair undersize and do a shrink/press fit to the bolt, but this can be tedious and would add to shop time.

Now that I finally got outside the box, consider a stack of washers, rather than the bushing.
If he gets washers of two different ODs, they will provide the grooves!
Run a nut down hard on the stack and it's rigid!
WL



-----Original Message----- From: towertalk-request@contesting.com
Sent: Wednesday, October 15, 2014 12:00 PM
To: towertalk@contesting.com
Subject: TowerTalk Digest, Vol 142, Issue 27

Send TowerTalk mailing list submissions to
towertalk@contesting.com

To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/towertalk
or, via email, send a message with subject or body 'help' to
towertalk-request@contesting.com

You can reach the person managing the list at
towertalk-owner@contesting.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TowerTalk digest..."


Today's Topics:

  1. Re: Anchor Bolt Material (Jon Pearl - W4ABC)


----------------------------------------------------------------------

Message: 1
Date: Wed, 15 Oct 2014 11:30:41 -0400
From: Jon Pearl - W4ABC <jonpearl@tampabay.rr.com>
To: TexasRF@aol.com, towertalk@contesting.com
Subject: Re: [TowerTalk] Anchor Bolt Material
Message-ID: <543E9321.5060101@tampabay.rr.com>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed

That's exactly what I was thinking, Gerald.

Marvin's greatest constraint is an oversized hole.  I would make a trip
to a machine shop with some appropriate sized anchor bolts and and have
the upper threaded portion necked-down!




73,


Jon Pearl - W4ABC
www.w4abc.com


On 10/15/2014 8:03 AM, TexasRF--- via TowerTalk wrote:
How about larger anchor bolts with upper six inches or so machined to fit
the base holes?

Could the base holes be reamed to a larger size?

K5GW







---
This email is free from viruses and malware because avast! Antivirus protection is active.
http://www.avast.com



------------------------------

Subject: Digest Footer

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


------------------------------

End of TowerTalk Digest, Vol 142, Issue 27
******************************************
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>