Has anyone used a post hole auger on a tractor to drive screw anchors??
I think they are a bit too fast, but might handle the job if properly
managed.
I'd rig a telescoping shaft, like on the pto driveshaft, to go between
the auger drive coupling and the anchor eye.
Wilson
W4BOH
-----Original Message----- From: towertalk-request@contesting.com
Sent: Wednesday, January 08, 2014 12:00 PM
To: towertalk@contesting.com
Subject: TowerTalk Digest, Vol 133, Issue 20
Send TowerTalk mailing list submissions to
towertalk@contesting.com
To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/towertalk
or, via email, send a message with subject or body 'help' to
towertalk-request@contesting.com
You can reach the person managing the list at
towertalk-owner@contesting.com
When replying, please edit your Subject line so it is more specific
than "Re: Contents of TowerTalk digest..."
Today's Topics:
1. Re: Fwd: Screw Anchor removal (Tom Nicholson)
2. Fwd: Fwd: Screw Anchor installation (Hans Hammarquist)
3. Unsubscribe, please. Thanks! (ai2n@twcny.rr.com)
4. Re: winch for tower (Richard (Rick) Karlquist)
5. Re: Unsubscribe, please. Thanks! (n8de@thepoint.net)
6. Re: Screw anchors (Paul Staupe)
7. Re: Tower raising and lowering system for sale (Frank Giambrone)
8. Re: Fwd: Screw Anchor installation (john@kk9a.com)
9. Re: Fwd: Screw Anchor removal (chetmoore)
----------------------------------------------------------------------
Message: 1
Date: Tue, 07 Jan 2014 17:36:33 -0500
From: Tom Nicholson <Gunsrus1942@Comcast.net>
To: David Blake <dhblake@yahoo.com>, "towertalk@contesting.com"
<towertalk@contesting.com>
Subject: Re: [TowerTalk] Fwd: Screw Anchor removal
Message-ID: <52CC8171.20201@Comcast.net>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
Thanks for the quick reply & as I thought, there has to be a mechanical
"advantage" employed!!! Hence the 4' pipe.
Thanks again.
Tom W1ALZ
On 1/7/2014 5:22 PM, David Blake wrote:
Not too difficult, just starting a screw -- I use a 4 foot
long pipe thru the eye and start turning. They actually
go in easier than you would think. Of course as it gets
deeper it becomes more difficult, thus the 4 foot pipe for
some leverage. You end up waking around and around
but the job has never taken more than a few minutes.
Where I have put them in Virginia there has been rock
and generally I have been lucky to be able to get by them
except one time when I just restarted the anchor 6 inches
further away.
In Ohio my soil had little rock and the anchor just went
right down.
73
Dave -N4DB-
On Tuesday, January 7, 2014 5:11 PM, Tom Nicholson
<Gunsrus1942@Comcast.net> wrote:
Having never installed one, how does one install one by hand? Dumb
question but I'm faced with maybe doing it & need to be an "inquiring"
mind.
Thanks for your input.
Tom W1ALZ
------------------------------
Message: 2
Date: Tue, 7 Jan 2014 18:14:57 -0500 (EST)
From: Hans Hammarquist <hanslg@aol.com>
To: towertalk@contesting.com
Subject: [TowerTalk] Fwd: Fwd: Screw Anchor installation
Message-ID: <8D0DA156A696108-2710-2EE11@webmail-d212.sysops.aol.com>
Content-Type: text/plain; charset="us-ascii"
Tom,
I can't say this is the right way but it worked for me. Flip through the
pictures and you will find how we simply banged on the anchor and turned
it a much as we could. A new hit and you could turn it again. It took
about half an hour to install one.
Hans - N2JFS
-----Original Message-----
From: Tom Nicholson <Gunsrus1942@Comcast.net>
To: Hans Hammarquist <hanslg@aol.com>
Sent: Tue, Jan 7, 2014 5:10 pm
Subject: Re: [TowerTalk] Fwd: Screw Anchor removal
Having never installed one, how does one install one by hand? Dumb
question but I'm faced with maybe doing it & need to be an "inquiring"
mind.
Thanks for your input.
Tom W1ALZ
On 1/7/2014 4:32 PM, Hans Hammarquist wrote:
I'm not ever sure you would be able to remove one, especially if it is a
little damaged by corrosion. My idea is to "just" add a new one by even the
slightest suspicion that you have an inferior anchor supporting your
tower. It
is not that hard to install a new one.
Hans - N2JFS
------------------------------
Message: 3
Date: Tue, 7 Jan 2014 23:42:04 +0000
From: <ai2n@twcny.rr.com>
To: towertalk@contesting.com
Subject: [TowerTalk] Unsubscribe, please. Thanks!
Message-ID: <20140107234204.TI46A.21656.root@cdptpa-web16>
Content-Type: text/plain; charset=utf-8
------------------------------
Message: 4
Date: Tue, 07 Jan 2014 16:08:14 -0800
From: "Richard (Rick) Karlquist" <richard@karlquist.com>
To: KJ6Y@aol.com, bill@grimwood.net, towertalk@contesting.com
Subject: Re: [TowerTalk] winch for tower
Message-ID: <52CC96EE.1010408@karlquist.com>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
On 1/7/2014 2:22 PM, KJ6Y@aol.com wrote:
Just wondering? How often do you tilt it over that you would need the
electric winch?
Skip, KJ6Y
This question somewhat oversimplifies the decision.
First of all, I have a MonstIR on a tilt plate. Thus
all antenna work is done with the tower tilted over,
never in the upright position. The tower has been
up and down many times to:
1. Debug the MonstIR when initially installed.
Dozens of times up and down. I will say that
once I got the MonstIR working, it has never
failed...yet.
2. Develop the homebrew tilt plate by trial and error,
now you can just buy one.
3. Fix the antenna to keep it from slipping on the mast
4. Diagnose and treat an insidious intermittent coax
connector on RG-218. Multiple times.
5. Fix an element that fell off (my bad, I forgot to
tighten the clamps).
6. Develop a modification to the MonstIR to use the
reflector and 2nd director as an 80 meter receiving beam.
A lot of trial and error here.
7. Periodic inspection and maintenance several times a
year for cable lubing etc. Replace cables "every 3
years" (right).
8. Make an emergency repair right before a contest
(Murphy's timing was impeccable).
9. Perform experiments like putting up a 130 foot
high 80 meter inverted vee.
Having said that, the supplied K2550 winch was
undercapacity for even the empty tower, not to mention
the MonstIR on top. The brake severely overheated
and I never trusted it. A replacement W3000 winch
had different but equally bad problems. I never trusted
it either. Either winch was like an athletic event
to turn using both hands. To me, the answer to how
many times a year is OK to hand winch the tower over
became zero.
Rick N6RK
------------------------------
Message: 5
Date: Tue, 07 Jan 2014 19:19:01 -0500
From: n8de@thepoint.net
To: ai2n@twcny.rr.com
Cc: towertalk@contesting.com
Subject: Re: [TowerTalk] Unsubscribe, please. Thanks!
Message-ID: <20140107191901.6dth005hwc4swo84@webmail.win.net>
Content-Type: text/plain; charset=ISO-8859-1; DelSp="Yes";
format="flowed"
Perhaps you need to read the BOTTOM of the emails from this reflector.
Full instructions are ALWAYS there.
73
Don
N8DE
Quoting ai2n@twcny.rr.com:
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
Message: 6
Date: Tue, 7 Jan 2014 18:58:43 -0600
From: Paul Staupe <staupe@gmail.com>
To: towertalk@contesting.com, Gunsrus1942@Comcast.net
Subject: Re: [TowerTalk] Screw anchors
Message-ID:
<CAOQ84auZqxUi4P1LbjkNF3WJUDd7+PKZkzmTV7ZTy6VXEkGAoA@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1
Tom,
I used 6' Chance screw anchors to install my 76' stick of Rohn 45G four
years ago. Soil here is about 1' of topsoil, clay underneath.
I dug through the topsoil and used a square steel bar about 6' long that
just fit through the opening on the Chance anchor and used the armstrong
method to grind them down through the clay to about 6" above ground. Lots
of sweat equity, but it only took about a half hour per anchor.
I have a 4L SteppIR at 77' and a 2L 40M Moxon at 95' and the anchors have
never budged.
Best regards,
Paul W0AD
Minneapolis
On Tuesday, January 7, 2014 5:11 PM, Tom Nicholson
<Gunsrus1942@Comcast.net>
wrote:
Having never installed one, how does one install one by hand? Dumb
question but I'm faced with maybe doing it & need to be an "inquiring"
mind.
Thanks for your input.
Tom W1ALZ
------------------------------
Message: 7
Date: Tue, 7 Jan 2014 18:54:33 -0500
From: Frank Giambrone <fsgiambrone@earthlink.net>
To: "William N. Goodman, CPA" <wgoodman@goodmancpa.com>
Cc: "<towertalk@contesting.com>" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Tower raising and lowering system for sale
Message-ID: <B1DC218F-78BC-480B-9F4E-59658710EC60@earthlink.net>
Content-Type: text/plain; charset=us-ascii
Pricing as always too strong. Please remove me from your list.
------------------------------
Message: 8
Date: Wed, 8 Jan 2014 01:46:53 -0000
From: <john@kk9a.com>
To: <TOWERTALK@contesting.com>
Subject: Re: [TowerTalk] Fwd: Screw Anchor installation
Message-ID: <F1A905510CEE4C49AECD65F451E7B166@kk9a>
Content-Type: text/plain; charset="iso-8859-1"
It is not a dumb question If you have soft soil with no rocks your should
be able to start the screw on an angle and use a lever to twist it in.
I am
not sure what you would do by hand if you have hard clay, shale and rocks
like I have. Generally speaking the easier it is to screw in the easier it
will pull out. Machines that install them measure the installation torque
to ensure adequate holding ability.
John KK9A
To:towertalk@contesting.com
Subject:Re: [TowerTalk] Fwd: Screw Anchor removal
From:Tom Nicholson <Gunsrus1942@Comcast.net>
Date:Tue, 07 Jan 2014 17:11:05 -0500
List-post:<towertalk@contesting.com">mailto:towertalk@contesting.com>
Having never installed one, how does one install one by hand? Dumb question
but I'm faced with maybe doing it & need to be an "inquiring" mind.
Thanks for your input.
Tom W1ALZ
------------------------------
Message: 9
Date: Tue, 7 Jan 2014 20:53:55 -0500
From: "chetmoore" <chetmoore@cox.net>
To: "'Tom Nicholson'" <Gunsrus1942@Comcast.net>,
<towertalk@contesting.com>
Subject: Re: [TowerTalk] Fwd: Screw Anchor removal
Message-ID: <002e01cf0c14$7d9500b0$78bf0210$@net>
Content-Type: text/plain; charset="US-ASCII"
Hi Tom,
20 years ago, I did mine by hand, using a pipe. On the new tower I found
that I could no longer do that by myself. 6 years ago I rented one of the
power augers from home depot. I got the trailer mounted unit You can rent
them for cheap. I used the augers that came with it to drill 4 holes close
together and then Shoveled them out. Take off the auger and Use the Kelly
bar to drive the anchors. Towed the trailer to the house and walked the
auger to the back yard. It took about 30 seconds to drive them in. I was
able to drive the anchors In less time than it took to line up the auger
trailer. We also drove 3 more For N4BAA and had the unit back to home depot
in less than 4 hours.
73
Chet N4FX
-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Tom
Nicholson
Sent: Tuesday, January 07, 2014 5:11 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Fwd: Screw Anchor removal
Having never installed one, how does one install one by hand? Dumb question
but I'm faced with maybe doing it & need to be an "inquiring"
mind.
Thanks for your input.
Tom W1ALZ
On 1/7/2014 4:32 PM, Hans Hammarquist wrote:
I'm not ever sure you would be able to remove one, especially if it is a
little damaged by corrosion. My idea is to "just" add a new one by even the
slightest suspicion that you have an inferior anchor supporting your tower.
It is not that hard to install a new one.
Hans - N2JFS
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
Subject: Digest Footer
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
End of TowerTalk Digest, Vol 133, Issue 20
******************************************
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk