Towertalk
[Top] [All Lists]

Re: [TowerTalk] Coax Seal yea or nay?

To: towertalk reflector <towertalk@contesting.com>
Subject: Re: [TowerTalk] Coax Seal yea or nay?
From: Bob K6UJ <k6uj@pacbell.net>
Date: Sun, 19 May 2013 20:21:02 -0700
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Pete,
I use 3M Scotchcote just as you do.  Gives a weather proof seal coating and 
like you said, the 
connectors stay dry and shiny.  

Bob
K6UJ

On May 19, 2013, at 12:03 PM, Pete Barletto wrote:

> 
> 
> Is 3M Scotchcote no longer in favor?  After a full wrap of tape,  a coating 
> of this messy stuff has kept connectors dry and shinny for years. OTOH I've 
> never used coax seal ... 
> 
> Pete 
> ku2c
> 
> 
> ________________________________
> From: K0DAN <k0dan@comcast.net>
> To: Steve Sacco NN4X <nn4x@embarqmail.com>; towertalk@contesting.com 
> Sent: Sunday, May 19, 2013 11:24 AM
> Subject: Re: [TowerTalk] Coax Seal yea or nay?
> 
> 
> Yes, Rescue Tape is the best I have found. Great stuff for sealing
> connectors, as well as a million other field repairs. It has almost no
> adhesive qualities and pretty much only sticks to itself, so it needs a
> tight wrap onto itself.
> 
> Not cheap but great product.
> 
> Many of us went the Coax Seal route back in the day, as it was
> well-advertised and was one of the only products of its type which made its
> way into the ham community. Today there are many other choices and I no
> longer use Coax Seal, much prefer combinations of butyl rubber, high quality
> electrical tape (Scotch Super 33) and Rescue Tape.
> 
> The Coax Seal goo that's left behind is pretty tenacious, however I have had
> some luck wiping it off using solvents like Goof Off, Goo Gone, etc. Often
> if it's a cheap connector, it's easier to just throw it away than to clean
> it.
> 
> 73
> de
> k0dan
> 
> -----Original Message----- 
> From: Steve Sacco NN4X
> Sent: May 19, 2013 12:49
> To: towertalk@contesting.com
> Subject: [TowerTalk] Coax Seal yea or nay?
> 
> I strongly dislike Coax Seal, for all the reasons cited.
> 
> Last week, I unwrapped a connection which consisted of a bunch of
> PL-259's and right angle connectors which I had foolishly wrapped in
> Coax Seal, and overwrapped with Scotch 88.  It took a incredibly long
> time to get it off the connectors so I could even disconnect them.  I
> found that the the Coax Seal had worked its way INSIDE the PL-259's
> under the outer shell, in addition to covering everything with a sticky
> residue that I have yet to find something to cut it with.
> 
> I've found the above problem repeatedly as I've modified things at my
> station that I did back when I was going through my Coax Seal phase.  I
> deeply regret that I went there back in the day.
> 
> MUCH better are products like silicon Rescue Tape.   It fuses to itself,
> forms a tight seal over the connectors, and is easily removed.  You need
> to cover it with a quality electrical tape to protect  it from UV, but
> that's not unreasonable.
> 
> 73,
> Steve
> NN4X
> EL98jh
> 
> 
> 
> ----------------------------------------------------------------------
>   Message: 1
>   Date: Sat, 18 May 2013 14:05:00 -0400
> From: K8RI <K8RI-on-TowerTalk@tm.net>
> To: towertalk@contesting.com
> Subject: Re: [TowerTalk] How close to salt water is close enough?
> 
> On 5/18/2013 11:51 AM, K7LXC@aol.com wrote:
>>>>       Products like coax seal are worth using liberally  wherever it can
>>>> be
>>> applied if needed.
>>> 
>>>        Just make sure you never have to take it off. It's  the WORST stuff
>>> in
>>> the world to get off of anything. You put in on a connector -  you have
>>> to
>>> throw the connector away.
>>> 
>> Why?  There is absolutely nothing electrically or mechanically wrong
>> with a connector just because it has coax seal on it.
>> 
>> I use Flooded Heat Shrink tubing.  The heavy 3M stuff the electrical
>> contractors use.  It's lined with Hot melt glue so when it's, it's
>> really sealed.  Getting it off, is not difficult., You cut it down one
>> side with a box cutter, pry up a corner and pull. Use a pair of pliers.
>>     It, like coax seal may leave residue behind. Hot glue in this case,
>> rather than pieces of coax seal. I ask again, so what?
>> 
>> Sure it looks crappy, but the connector underneath is clean and shiny.
>> It can be used again as if it were new and when a new coating of coax
>> seal or heat shrink is put in place it is as good as it was the first
>> time and at this point looks no different.
>> 
>> The only problem is the connector may be "sticky, so either put it in a
>> baggie, plastic package or just don't drop it in the dirt.
>> 
>> BTW I think Mineral spirits will clean coax seal off.
>> Even connectors wrapped with tape get sticky.
>> 
>> Now you could resort to a layer of tape wrong side out, but unless done
>> well can be a source of leaks. Yah, I know many swear by it because it
>> leaves the connector shiny. You can also wrap the connection with one or
>> two layers of Saran wrap which really seals when covered with
>> "stretched" tape wound past its ends, but these are extra steps that
>> serve a only as a cosmetic.  I'm a firm believer of the KISS approach
>> which is the most durable, simple, and effective.
>> 
>> Then I wonder why the obsession with reusing connectors.  Most hams use
>> a $3.00 PL259 if they are consciousnesses.  Well, no, most use the cheap
>> stuff found at swaps instead of buying the "good stuff". That gob of
>> solder on the center connectors has ruined more female connectors than
>> just about any thing else.
>> 
>> I realize there are many hams for whom purchasing a dozen PL259s is hard
>> on the budget.  I know many and was there once .. no, several times
>> myself, and I would have gladly used connectors with a little coax seal
>> on them because it doesn't hurt anything except it lets others know you
>> are using a <gasp> used connector.
>> 
>> Many of us gladly use, used connectors on large coax where new ones are
>> over a $100.
>> 
>> But why care if some coax seal (Electrical putty) is stuck on the
>> outside of a connector?  It feels icky?  Just don't drop it in the dirt.
>> <:-))
>> 
>> 
>> End of Rant.<:-))
>> 
>> 73
>> 
>> Roger (K8RI)
>> 
>> 
>> 
>> 
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>