Hi Les,
Can you please tell me what crimping tool you use and where
to get them?? Also to correct connectors for RG-213...
Thanks Les,
73,
Ted K2QMF
On Sat, 12 Feb 2011 15:45:57 -0500 Les Kalmus <w2lk@bk-lk.com> writes:
> Peter,
>
> I use crimp connectors a lot and have not had any problems like
> this.
> I looks like the crimp was not tight enough which is most likely
> from
> either the wrong die, not enough pressure or crimping too far behind
> the
> head of the connector.
> I can bring the crimper I use to the next meeting for you to take a
> look
> at if you like.
>
> Les W2LK
>
> On 2/12/2011 1:11 PM, Peter Dougherty wrote:
> > The copper shield itself isn't visible in the shot, but it's under
> the
> > ferrule that's pulled back. That knurled portion behind the barrel
> of the
> > white heat-shrunk PL-259 (between the heat shrink and the part you
> rotate
> > onto the SO-239) should not be visible. That knurled bit should
> have copper
> > shield and crimped ferrule over top of it (and optional
> heat-shrink). The
> > "Amp Out" connector (below it) isn't in clear focus in that shot,
> but it's
> > still good. The "failed" one hasn't failed completely, the centre
> is still
> > soldered in and the electrical connections are solid (it's the
> lead down
> > from the tower). I haven't gotten around to replacing it yet but
> when I get
> > some time that's high on the priorities list, assuming there's any
> slack
> > left in the basement - it's pretty snug right now.
> >
> >
> > ------
> >
> > - pjd
> >
> >
> > -----Original Message-----
> > From: towertalk-bounces@contesting.com
> > [mailto:towertalk-bounces@contesting.com] On Behalf Of Jim W7RY
> > Sent: Saturday, February 12, 2011 12:10 PM
> > To: Peter Dougherty; 'Michael W5NIG'; towertalk@contesting.com
> > Subject: Re: [TowerTalk] Crimp-on PL259 et al
> >
> > I see a connector covered with heatshrink and no shield pulling
> away. ????
> >
> > Jim W7RY
> >
> >
> > --------------------------------------------------
> > From: "Peter Dougherty"<w2irt@verizon.net>
> > Sent: Saturday, February 12, 2011 8:36 AM
> > To: "'Michael
> W5NIG'"<tower@coffeepower.net>;<towertalk@contesting.com>
> > Subject: Re: [TowerTalk] Crimp-on PL259 et al
> >
> >> Here are two photos of what I mean by crimp-on PL-259s failing.
> >>
> >>
> >
>
http://s291.photobucket.com/albums/ll290/W2IRT/Towers%20and%20Antennas/?a
cti
> >> on=view¤t=Crimp-fail-1.jpg
> >>
> >
>
http://s291.photobucket.com/albums/ll290/W2IRT/Towers%20and%20Antennas/?a
cti
> >> on=view¤t=Crimp-fail-3.jpg
> >>
> >> You can see the braid/ferrule has pulled back from the main part
> of the
> >> connector. When installed this was flush against the body of the
> >> connector.
> >> Eventually this will pull right off. If I hadn't soldered the
> center
> >> conductor in (some are intended to just crimp on) the coax would
> pull
> >> right
> >> out of the connector. When, in the middle of CQWW 2009, my 160 TX
> antenna
> >> had failed I went outside and found the coax laying on the sodden
> ground
> >> having failed exactly in that manner.
> >>
> >> After the contest was over I pulled somewhat-gently on every coax
> sticking
> >> down from the Ameritron antenna switchbox and two more pulled
> apart. At
> >> that
> >> point I still trusted the connectors, but I insisted on soldering
> the
> >> centers after that. When more failed inside the shack, on patch
> cables,
> >> etc,
> >> I gave up and went back to solder-only.
> >>
> >>
> >> ------
> >>
> >> - pjd
> >>
> >>
> >> -----Original Message-----
> >> From: towertalk-bounces@contesting.com
> >> [mailto:towertalk-bounces@contesting.com] On Behalf Of Michael
> W5NIG
> >> Sent: Saturday, February 12, 2011 9:17 AM
> >> To: towertalk@contesting.com
> >> Subject: [TowerTalk] Crimp-on PL259 et al
> >>
> >> ***Quote***
> >> Date: Fri, 11 Feb 2011 17:39:52 -0500
> >> From: "Peter Dougherty"<w2irt@verizon.net>
> >> Subject: Re: [TowerTalk] Crimp-on PL259
> >> To:<nf4l@nf4l.com>, "'towertalk reflector'"
> >> <towertalk@contesting.com>
> >> Message-ID:<018401cbca3c$99d3e380$cd7baa80$@net>
> >>
> >> Mike, I have to say my experiences with crimp-on connectors has
> ranged
> >> from
> >> convenient to catastrophic failure, with the latter being
> commonplace. I'd
> >> say about 75% of the crimp connectors have failed within the
> three years
> >> they've been installed, both inside and outside. Once any stress
> goes on
> >> the
> >> cable (just gravity for the most part), it's just been a matter
> of time
> >> before it fails in my experience. I'm using connectors from The
> RF
> >> Connection as well as the crimp tool they provided and I use a
> cable-prep
> >> tool from DX Engineering. This summer all my remaining crimp-on
> connectors
> >> will be cut off and new solder-type (inside) and clamp-type
> connectors
> >> (outside) will go on instead. I'm quite intrigued about this new
> clamp
> >> type
> >> and I'd personally like to get more first-hand experiences
> before
> >> shotgunning out all the existing connectors.
> >>
> >> ***UnQuote***
> >>
> >> Very interesting! I've been using a coax prep tool for quite a
> while
> >> now,
> >> it's a
> >> love/hate relationship, hi hi. works well though, all in all. I
> just
> >> bought a crimp
> >> tool with the extra set of jaws at the last hamfest that I
> attended. I
> >> haven't had
> >> opportunity yet to us one on regular rg8 or 213 but have had the
> pleasure
> >> of
> >>
> >> installing
> >> a few on 8x. I've got to say Im impressed with it in that
> capacity! good
> >> compression
> >> on the shield and great tension on the jacket. Usually the thing
> is
> >> subject
> >>
> >> to twisting
> >> etc and if the coax is moving a lot I eventually might have
> issues with
> >> it.
> >> I"ll be testing
> >> it on 8/213 coax at easy to get to places to see how it goes when
> I get
> >> back
> >>
> >> on my tower
> >> project!
> >>
> >> Michael de W5NIG
> >>
> >>
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >>
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> >>
> >>
> >> -----
> >> No virus found in this message.
> >> Checked by AVG - www.avg.com
> >> Version: 10.0.1204 / Virus Database: 1435/3439 - Release Date:
> 02/12/11
> >>
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
> >
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
____________________________________________________________
$65/Hr Job - 25 Openings
Part-Time job ($20-$65/hr). Requirements: Home Internet Access
http://thirdpartyoffers.juno.com/TGL3141/4d56f2849447e249107st04vuc
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|