Towertalk
[Top] [All Lists]

Re: [TowerTalk] [CQ-Contest] Yaesu rotor conversion to 220 volts

To: n4zr@contesting.com
Subject: Re: [TowerTalk] [CQ-Contest] Yaesu rotor conversion to 220 volts
From: Krishna Kanakasapapathi <kkanakas@cisco.com>
Date: Fri, 04 Jun 2010 16:05:16 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Marko,
Instead of messing with the control box supply, why not just use an 
external conversion transformer that is
rated to handle the needed power? Might be safer.220V to110V.
Krish
w4vku

Pete Smith wrote:
> I agree with Dale about the techs - one named Jerry, whose last name 
> I've forgotten, is particularly familiar with rotators.
>
> That said, I have looked at the schematic diagram for the 800SA, and the 
> power transformer doesn't have any switchable taps, nor are there any 
> clever switching power supply devices to enable a wide range of input 
> voltages.  The manual cautions you to be sure to use the AC voltage 
> shown on the sticker on the back, and makes no reference to changing 
> input voltages.
>
> 73, Pete N4ZR
>
> The World Contest Station Database, updated daily at www.conteststations.com
> The Reverse Beacon Network at http://reversebeacon.net, blog at 
> reversebeacon.blogspot.com
>
>
> On 6/4/2010 10:19 AM, Dale L Martin wrote:
>   
>> If you haven't done so, Marko, may I recommend taking a look at the
>> rotator manuals/schematics.  I think you may find that at least one,
>> if not both, rotators are DC and the listed AC inputs are 117 and 220.
>>
>> Since there are not mechanical/electrical change instructions and
>> nothing visible on the schematics for each, I'm betting they are both
>> capable of 117 and 220 V-AC operation -- in the 450, I think it was,
>> you may have to swap out a fuse to a lower current value, but that's
>> it.
>>
>> I'd keep trying Vertex/Yaesu.  I've always had good luck talking with
>> their techs.
>>
>> 73,
>> dale, kg5u
>>
>>
>>    
>>     
>>>>        
>>>>         
>>>>> Hello,
>>>>> In next couple days I'm looking to buy Yaesu rotor in US, either
>>>>> G-450A or G-800SA and ship directly into location for fall contest.
>>>>> I will not see the rotor until November.
>>>>> Does anyone here know how to exactly convert either of these rotor
>>>>> models for 220 V operation ?  Information I found in a web is bit
>>>>> confusing and Vertex phone line puts you on eternal hold and
>>>>> eventually hangs up.
>>>>> 73 de Marko N5ZO
>>>>> _______________________________________________
>>>>> CQ-Contest mailing list
>>>>> CQ-Contest@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>>>
>>>>>
>>>>>
>>>>>          
>>>>>           
>>>> _______________________________________________
>>>> CQ-Contest mailing list
>>>> CQ-Contest@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>>
>>>>
>>>>
>>>>        
>>>>         
>>> _______________________________________________
>>> CQ-Contest mailing list
>>> CQ-Contest@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>>      
>>>       
>> _______________________________________________
>> CQ-Contest mailing list
>> CQ-Contest@contesting.com
>> http://lists.contesting.com/mailman/listinfo/cq-contest
>>
>>
>>    
>>     
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>   

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>